Triangulation sensor with background suppression, 250 mm adjustable detection range, blue light, light/dark on, NPN output, fixed cable, Miniature design, Easy to use, Full metal thread mounting, Highly visible LEDs for Power ON and switching state, Not sensitive to ambient lightfa
Triangulation sensor with background suppression, 250 mm adjustable detection range, blue light, light/dark on, pnp output, fixed cable, Miniature design, Easy to use, Full metal thread mounting, Highly visible LEDs for Power ON and switching state, Not sensitive to ambient lightfa
Triangulation sensor with background suppression, 250 mm adjustable detection range, blue light, light/dark on, npn output, M8 plug 4-pin, Miniature design, Easy to use, Full metal thread mounting, Not sensitive to ambient light, Very bright, highly visible blue light spotfa
Triangulation sensor with background suppression, 250 mm adjustable detection range, blue light, light/dark on, pnp output, M8 plug 4-pin, Miniature design, Easy to use, Full metal thread mounting, Highly visible LEDs for Power ON and switching state, Not sensitive to ambient lightfa
See Overview: Pepperl+Fuchs H-System isolated barriers connect intrinsic safety barriers to a termination board ... signal loop between field and control side is closed by plugging in the module. The H-System is an efficient solution in medium-sized to large systems in combination with process control systems. No expensive and manual individual wiring thanks to fixed ...
See Overview: Our H-System signal converters receive signals from a hazardous area instrument ie, temperature sensors, potentiometers or load cells and then convert and condition them into signals such as 0/420mA or 0/210V ... See Overview: Our H-System signal converters receive signals from a hazardous area instrument i.e., temperature sensors, potentiometers or load cells and then convert and condition them into signals s ...
See Overview: Designed to compliment H-system termination boards, H-system accessories from Pepperl+Fuchs provide a full range of diagnostic and alarm monitoring capabilities ... Designed to compliment the H-System and its architecture, H-System accessories provide a full range of diagnostic and alarm monitoring capabilities. The HART or fault monitoring boards can easily be added, along with tagging strips and custom length ...
See Overview: HART Interface Solution H-System termination boards for integration of the Mux2700 in several DCS are available from Pepperl+Fuchs ... The HART Communication Board is used with the H-System HART Multiplexer HID MUX2700. With the redundant power supply and RS485 terminals you get maximum availability for your application. Other termination boards for integration of the Mux2700 in ...
See Overview: Each H-System HART Multiplexer (HID MUX 2700) from Pepperl+Fuchs provides communication to 32 HART devices This allows up to 992 field devices to be addressed via one RS485 interface with 31 H-System HART Multiplexers ... Each H-System HART Multiplexer (HID MUX 2700) provides communication to 32 HART devices . This allows up to 992 field devices to be addressed via one RS485 interface with 31 H-System HART Multiplexers. ...
See Overview: H-System termination boards from Pepperl+Fuchs connect intrinsic safety barriers, creating an interface connection between field devices in a hazardous location & the process automation system Our termination boards reduce mounting ... H-System Termination Boards Features of the termination boards at a glance: Solutions for all leading process control systems with control system-specific connectors Tested with process control and safety systems from leading DCS companies Control ...
See Overview: H System switch amplifiers from Pepperl+Fuchs consist of three primary components: the power supply, the transistor switch amplifier and the output stage Galvanic isolation separates the input, output and power supply circuits ... ( NAMUR ). This means the residual voltage in normal operation is approximately 8 VDC and the short circuit current is approximately 8 mA. The switch points are typically between 1.2-2.1 mA. Many Pepperl+Fuchs isolators offer optional lead breakage and ...
See Overview: Pepperl+Fuchs H-System relay modules switch circuits inside the hazardous area These relay modules can be used to sense external on/ off conditions and to control a variety of external devices ... See Overview: Pepperl+Fuchs H-System relay modules switch circuits inside the hazardous area. These relay modules can be used to sense external on/ off conditions and to control a variety of external ...
See Overview: Pepperl+Fuchs H-System interface modules easily snap on to the termination boards with no wires or tools needed H-System interface modules feature high channel density, reduced space requirements, single loop integrity & simple ... H-System Interface Modules H-System interface modules are very easy to handle . They are just snapped onto pre-wired termination boards —no wires, no tools. The modules can be installed horizontally or vertically without spacers or power reduction ...
Explore the Pepperl+Fuchs knowledge base to learn more about the electrical connections of inductive sensors ... current 0 mA ... 200 mA No-load current 20 mA Alternating-Current Voltage 20 V ... 250 V Sensor type WS, WÖ, W, W4 Wiring diagram according to EN 60947-5-2 NC contact and NO contact Example: NC contact WÖ/UÖ Typical data Voltage drop "ON": 6 V Residual ...
11-20/111Items Per Page:
No results found?
Hint: Use wildcard character * before your search term, modify your search, check your search terms for misspellings, or contact us with your specific request.