Yhteydenotto, Koneautomaatio
+358 20 7861 290
Yhteydenotto, Prosessiautomaatio
+358 20 7861 291

Double sheet sensor UDCM-30GS-3EP1-IO-0,2M-V19

UDCM-30GS-3EP1-IO-0,2M-V19
  • Ultrasonic system for reliable detection of no, one, or two overlapping sheet materials, preferably sheet metal
  • Insensitive to printing, colors, and shining surfaces
  • Perpendicular or inclined sensor mounting relative to the sheet plane possible
  • Integrated alignment aid
  • IO-Link Interface for process data, parameterization and diagnosis
  • Synchronization options
  • No teach-in required

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Lataa koko tietolomake PDF-tiedostona:


Ote tietolomakkeesta: Tekniset tiedot  UDCM-30GS-3EP1-IO-0,2M-V19

General specifications
Sensing range50 ... 150 mm , optimal distance: 80 mm
Transducer frequencyapprox. 85 kHz
Memory
Non-volatile memoryEEPROM
Write cycles300000
Indicators/operating means
LED greenindication: single sheet detected
flashing (1 Hz) - standby mode
flashing with short break (1 Hz) - IO-Link mode
LED yellowindication: no sheet detected (Air)
LED redindication: double sheet detected
flashing: device error
Electrical specifications
Operating voltage18 ... 30 V DC , ripple 10 %SS
No-load supply current≤ 100 mA
Power consumption≤ 1500 mW
Time delay before availability≤ 300 ms
Interface
Interface typeIO-Link
IO-Link revision1.1
Device profileIdentification and Diagnosis - I&D
Process dataInput: 16 Bit
- measurement value 8 Bit
- selected threshold set 2 Bit
- switching signals 3 Bit
Output: 8 Bit
- threshold set 2 Bit
- disable transducer 1 Bit
Vendor ID1 (0x0001)
Device ID3148292 (0x300A04)
Transfer rateCOM1 (4.8 kbits/s)
Min. cycle time22.4 ms
SIO mode supportyes
Compatible master port typeClass A (use adapter cable listed in accesories)
Class B (use 3-pole adapter or 3-wire cable)
Input/Output 1
DesignationSYNC
Input/output type1 synchronization connection, bidirectional
0 Level0 ... 1 V
1 Level2.5 V ... UB
Input impedance> 22 kΩ
Output rated operating currentcurrent source < 2.5 mA
Pulse length0.4 ... 6 ms with external control, low active
Synchronization frequency
Common mode operation≤ 140 Hz
Multiplex operation≤ 140 Hz /n, n = number of sensors , n ≤ 10
Input/Output 2
DesignationIN2/FEEDBACK
Input/output typeinput or output programmable via IO-Link :
input for selection of a threshold set (factory default)
output as feedback output
Input typedigital input
Signal0-level: 0 ... + 1V
1-level: +UB - 1 V ... +UB
Input impedance≥ 60 kΩ
Pulse length≥ 100 ms
Output typePNP
Rated operating current8 mA
Voltage drop< 3 V
Fusingreverse polarity protected , overload and short-circuit protected
Input
DesignationIN1/TEACH
Input type0-level: 0 ... + 1V
1-level: +UB - 1 V ... +UB
Pulse length≥ 100 ms
Impedance≥ 60 kΩ
Output
DesignationOUT 1 ... 3
Number3
Output functionOUT 1: single sheet detected
OUT 2: double sheet detected
OUT 3: no sheet detected (air)
Output typePush-pull (4 in 1) output , NC contact ( programmable )
Rated operating current100 mA per output
Voltage drop≤ 3 V
Switch-on delay30 ms (programmable)
Switch-off delay30 ms (programmable)
Pulse extensioncan be activated (100 ms or IO-Link cycle time)
Fusingreverse polarity protected , overload and short-circuit resistant
Compliance with standards and directives
Standard conformity
StandardsEN IEC 60947-5-2:2020
IEC 60947-5-2:2019
IEC 61131-9 / IO-Link V1.1.3
Approvals and certificates
UL approvalcULus Listed, General Purpose, Class 2 Power Source
CCC approvalCCC approval / marking not required for products rated ≤36 V
Ambient conditions
Ambient temperature0 ... 60 °C (32 ... 140 °F)
Storage temperature-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection typefixed cable with plug
Housing length
Ultrasonic transmitter56 mm
Ultrasonic receiver78 mm
Housing diameter
Ultrasonic transmitter30 mm
Ultrasonic receiver30 mm
Degree of protectionIP65
Material
HousingStainless steel 1.4305/AISI 303, polyamide plastic parts
Transducerepoxy resin/hollow glass sphere mixture; polyurethane foam
Connector
ThreadingM12 x 1
Number of pins8
Cable
Cable diameter4.3 mm
Bending radius5 x diameter , fixed
MaterialPUR
Colorblack
Lengthapprox. 200 mm
Mass300 g
Tightening torque, fastening screwsmax. 30 Nm

Classifications

SystemClasscode
ECLASS 13.027272801
ECLASS 12.027272801
ECLASS 11.027272801
ECLASS 10.0.127272801
ECLASS 9.027272801
ECLASS 8.027272801
ECLASS 5.127272801
ETIM 9.0EC001847
ETIM 8.0EC001847
ETIM 7.0EC001847
ETIM 6.0EC001847
ETIM 5.0EC001847
UNSPSC 12.141111960

Details: UDCM-30GS-3EP1-IO-0,2M-V19

Function

The ultrasonic double-sheet detector is used wherever automatic differentiation between single and double sheets is necessary to protect machines or prevent rejects. The double sheet detection is based on the ultrasonic thru-beam principle.

The following situations can be detected:

  • No sheet, i. e. air

  • Single sheet

  • Double sheet or multiple sheets (a statement on the number of sheets is not possible here)

The signals are evaluated by a microprocessor system. As a result of the evaluation, corresponding switching outputs are set and the result of the evaluation is communicated via the IO-Link interface.

Product Documentation: UDCM-30GS-3EP1-IO-0,2M-V19

Language Selection:
Brief InstructionsKieliTiedostotyyppiTiedoston koko
Commissioning instruction for series UDC-/UDCM-30GS-* / Inbetriebnahmeanleitung für Serie UDC-/UDCM-30GS-*ALLPDF419 KB
Safety and Security Documentation
KäyttöohjeFINPDF143 KB
Manuals
Manual UDC-/UDCM-*GS-*-IO*-Series Parameterization of Ultrasonic Double Sheet Sensors with IO-Link InterfaceENGPDF4602 KB
Parameter Information
IO-Link Parameter Datasheet UDCM-30GS-3EP1-IO-0,2M-V19ENGPDF582 KB

Design / Simulation: UDCM-30GS-3EP1-IO-0,2M-V19

Language Selection:
CADKieliTiedostotyyppiTiedoston koko
CAD 3-D / CAD 3-DALLSTP6723 KB
CAE
CAE EPLAN Data Portal / CAE EPLAN Data PortalALLLINK---
CAE EPLAN macro EDZ / CAE EPLAN Makro EDZALLEDZ73 KB

Approvals: UDCM-30GS-3EP1-IO-0,2M-V19

Language Selection:
CertificatesSertifikaatin nroKieliTiedostotyyppiTiedoston koko
Canada USA UL Ordinary LocationUL-US-2140156-4 / UL-CA-2133660-4ALLPDF284 KB
IO-Link Manufacturer DeclarationCERT-6560ALLPDF290 KB
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)DOC-6787ALLPDF33 KB
UK Declaration of Conformity (P+F) / UK-Konformitäterklärung (P+F)DOC-6788ALLPDF31 KB

Software: UDCM-30GS-3EP1-IO-0,2M-V19

Language Selection:
Device Description Files/DriversJulkaisutiedotTiedostotyyppiTiedoston koko
IODD for UDCM-30GS-3EP1 / IODD für UDCM-30GS-3EP1V1.00.000 / 2022-03-30ZIP242 KB
DTM (Device Type Manager) Package for UDC-18GS*/UDC-30GS* ultrasonic sensors / DTM (Device Type Manager) Package für UDC-18GS*/UDC-30GS* UltraschallsensorenV1.1.0.0 / 08-08-2022ZIP16847 KB
Software Tools
IO-Link Offline Parameterization Tool / IO-Link Offline-ParametriertoolV1.00.006 / 2022-07-10ZIP96138 KB

Liitännäistuotteet: UDCM-30GS-3EP1-IO-0,2M-V19

Accessories
Cordset M8 socket straight to M8 plug straight A-coded, 4-pin, PUR cable 3-core black, shieldedfa
Cordset M8 socket straight to M8 plug straight A-coded, 4-pin, PUR cable 3-core black, shieldedfa
Female cordset single-ended M12 straight A-coded, 8-pin, PUR cable black, UL approved, drag chain suitablefa
IO-Link master, supply via USB port or separate power supply, LED indicators, M12 plug for sensor connectionfa
Cordset for IO-Link M12 socket straight A-coded 8-pin to M12 plug straight A-coded 4-pin, PUR cable black, UL approved, drag chain suitablefa
Mounting bracket for double sheet metal monitor, Special design to avoid reflections, Large adjustment range of sensor head spacingfa
Mounting aidfa

Pepperl+Fuchs offers you various downloadable documents containing knowledge on ultrasonic sensors.