Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Lataa koko tietolomake PDF-tiedostona:
Tuotekuvaus |
---|
Signal converter SSI/RS 232/Parallel |
Electrical specifications | ||
---|---|---|
Rated operating voltage | 18 ... 30 V DC | |
Rated operating current | ≤ 200 mA | |
Input 1 | ||
Input type | SSI | |
Input format | Gray code, binary code | |
Resolution | 13, 21, or 25 bit | |
Input frequency | 100 Hz ... 1 MHz | |
Input 2 | ||
Input type | HTL (Hold) | |
Signal voltage | ||
High | ≥ 10 V | |
Low | ≤ 3 V | |
Internal resistor | 5 kΩ | |
Output | ||
Number/Type | Parallel | |
Output rated operating current | Gray-Code, Binary-Code, BCD-Code | |
Contact loading | max. 35 V on COM+ (Short-circuit resistance up to 27 V) max. 1.2 kA ± 10 % at 24 V (Ri = 600 Ω) |
|
Ambient conditions | ||
Ambient temperature | 0 ... 45 °C (32 ... 113 °F) | |
Mechanical specifications | ||
Connection | screw terminals , max. core cross-section 0.34 ... 2.5 mm2 | |
Mass | approx. 190 g |
System | Classcode |
---|---|
ECLASS 13.0 | 27210904 |
ECLASS 12.0 | 27210904 |
ECLASS 11.0 | 27210904 |
ECLASS 10.0.1 | 27210904 |
ECLASS 9.0 | 27210904 |
ECLASS 8.0 | 27210904 |
ECLASS 5.1 | 27210904 |
ETIM 9.0 | EC002918 |
ETIM 8.0 | EC002918 |
ETIM 7.0 | EC002918 |
ETIM 6.0 | EC002918 |
ETIM 5.0 | EC002475 |
UNSPSC 12.1 | 39121007 |
K23-SSI/R2/25B-C represents a small and low-cost, but highly performant converter for industrial applications, where the information of a sensor or encoder with SSI interface needs to be converted to a parallel signal or a serial RS 232 data format. Also it is possible to convert serial RS 232 data to a parallel format. The unit has been designed as a compact module with 12 screw terminals, a 9-pin and a 25-pin Sub-D connector (female). The housing is suitable for standard DIN rail mounting.
Applicable encoders and sensors:
Single-turn or multi-turn absolute encoders and all similar sensors using a standard SSI interface (6 .. 25 bits of resolution with binary or Gray code). The unit can operate in either master mode (clock signal generated by the unit), or in slave mode (clock signal generated by a remote device).
Remark about the encoder resolution:
The unit provides settings for the standard resolutions of 13 bits, 21 bits and 25 bits. In general, for sensors with other resolutions you can use the next higher setting (i. e. set the unit to 21 bits with a sensor of 16 bits).
Depending on brand and specification of the encoder, in some cases it may be necessary to blank out the surplus bits by using the bit blanking function described later. In general however, the unit should work perfectly also without special bit blanking.
Manuals | Kieli | Tiedostotyyppi | Tiedoston koko |
---|---|---|---|
Operating Instructions K23-SSI/R2/25B-C | ENG | 238 KB |
Software Tools | Julkaisutiedot | Tiedostotyyppi | Tiedoston koko |
---|---|---|---|
software tool to configure K23-SSI devices and TC-LCDC displays / Parametrier- und Konfigurationssoftware für K23-SSI und TC-LCDC | 08/2021 | ZIP | 85353 KB |