Serviceline Industrial Sensors
Serviceline Explosion Protection
Inductive sensor NJ10-30GM50-E2-V1-3G-3D
- 10 mm flush
- ATEX-approval for zone 2 and zone 22
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH, also apply to Pepperl+Fuchs AG.
Download the complete datasheet as a PDF:
Datasheet excerpt: Technical data of NJ10-30GM50-E2-V1-3G-3D
| General specifications | ||
|---|---|---|
| Switching function | Normally open (NO) | |
| Output type | PNP | |
| Rated operating distance | 10 mm | |
| Installation | flush | |
| Output polarity | DC | |
| Assured operating distance | 0 ... 8.1 mm | |
| Actual operating distance | 9 ... 11 mm typ. 10 mm | |
| Reduction factor rAl | 0.32 | |
| Reduction factor rCu | 0.3 | |
| Reduction factor r304 | 0.66 | |
| Reduction factor rBrass | 0.4 | |
| Output type | 3-wire | |
| Nominal ratings | ||
| Operating voltage | 10 ... 30 V DC | |
| Switching frequency | 0 ... 1300 Hz | |
| Hysteresis | 3 ... 15 typ. 6 % | |
| Reverse polarity protection | reverse polarity protected | |
| Short-circuit protection | pulsing | |
| Voltage drop | ≤ 3 V | |
| Voltage drop at IL | ||
| Voltage drop IL = 200 mA, switching element on | 1 ... 2 V typ. 1.5 V | |
| Operating current | ≤ 200 mA | |
| Off-state current | 0 ... 0.5 mA typ. 0.01 mA | |
| No-load supply current | ≤ 15 mA | |
| Time delay before availability | ≤ 100 ms | |
| Switching state indicator | LED, yellow | |
| Compliance with standards and directives | ||
| Standard conformity | ||
| Standards | EN 60947-5-2:2007 EN 60947-5-2/A1:2012 IEC 60947-5-2:2007 IEC 60947-5-2 AMD 1:2012 |
|
| Approvals and certificates | ||
| UL approval | cULus Listed, General Purpose, Class 2 Power Source | |
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) | |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Mechanical specifications | ||
| Connection type | Connector plug M12 x 1 , 4-pin | |
| Housing material | Stainless steel 1.4305 / AISI 303 | |
| Sensing face | PBT | |
| Degree of protection | IP66 / IP67 | |
| Data for application in connection with hazardous areas | ||
| Equipment protection level | Gc (nA) , Dc | |
| Equipment protection level Gc (nA) | ||
| Type of protection | "n" | |
| CE marking | [*PD-Z02586A*] | |
| Certificates | ||
| ATEX certificate | PF15CERT3754X | |
| ATEX marking |  II 3G Ex nA IIC T6 Gc |
|
| Standards | EN 60079-0:2012+A11:2013 , EN 60079-15:2010 | |
| Surge protection | The protection against transient overvoltage with amplitude U is realized. U = 500 V at 1.2/50 µs, 500 Ω |
|
| Possible characteristics | maximum operating voltage UBmax , maximum load current ILmax , minimum series resistance RV , maximum analog output voltage UAmax , maximum analog output current IAmax | |
| Maximum permissible ambient temperature | Also observe the maximum permissible ambient temperature stated in the general technical data. Keep to the lower of the two values. at UBmax = 30 V , IL = 200 mA : 57 °C (134.6 °F) at UBmax = 30 V , IL = 100 mA : 60 °C (140 °F) at UBmax = 30 V , IL = 50 mA : 60 °C (140 °F) |
|
| Equipment protection level Dc | ||
| Type of protection | Protection by enclosure "tc" | |
| CE marking | [*PD-Z02586A*] | |
| Certificates | ||
| ATEX certificate | PF15CERT3774X | |
| ATEX marking | II 3D Ex tc IIIC T80°C Dc |
|
| Standards | EN 60079-0:2012+A11:2013 , EN 60079-31:2014 | |
| Possible characteristics | maximum operating voltage UBmax , maximum load current ILmax , minimum series resistance RV , maximum analog output current IAmax , maximum analog output voltage UAmax | |
| Maximum permissible ambient temperature | Also observe the maximum permissible ambient temperature stated in the general technical data. Keep to the lower of the two values. at UBmax = 30 V , IL = 200 mA : 57 °C (134.6 °F) at UBmax = 30 V , IL = 100 mA : 60 °C (140 °F) at UBmax = 30 V , IL = 50 mA : 60 °C (140 °F) |
|
| General information | ||
| Scope of delivery | 2 self locking nuts in scope of delivery | |
| Use in the hazardous area | see instruction manuals | |
Documents: NJ10-30GM50-E2-V1-3G-3D
| Instruction manuals | Language | File Type | File Size |
|---|---|---|---|
| Инструкции | BUL | 151 KB | |
| Návod k poużití | CZE | 145 KB | |
| Instruktions manual | DAN | 144 KB | |
| Instruction manual | ENG | 149 KB | |
| Kasutusjuhend | EST | 140 KB | |
| Käyttöohje | FIN | 140 KB | |
| Manuel d'instructions | FRA | 147 KB | |
| Betriebsanleitung | GER | 150 KB | |
| Οδηγίες χρήσης | GRE | 155 KB | |
| Handleiding | HOL | 145 KB | |
| Instruction manual / Betriebsanleitung | HRV | 144 KB | |
| Használati útmutató | HUN | 147 KB | |
| Manuale di istruzioni | ITA | 144 KB | |
| Lietošanas pamācība | LAV | 144 KB | |
| Instrukciju vadovas | LIT | 146 KB | |
| Instrukcja obsługi | POL | 147 KB | |
| Manual de instruções | POR | 146 KB | |
| Manual de utilizare | RON | 145 KB | |
| Návod na poużitie | SLK | 145 KB | |
| Navodila za uporabo | SLV | 143 KB | |
| Manual de instrucciones | SPA | 146 KB | |
| Manual | SWE | 143 KB |
CAD+CAE: NJ10-30GM50-E2-V1-3G-3D
| CAD | File Type | File Size | |
|---|---|---|---|
| 3-D model in IGS format / 3-D-Modell im IGS-Format | IGS | 1245 KB | |
| 3-D model in STP format / 3-D-Modell im STP-Format | STP | 317 KB |
Approvals+Certificates: NJ10-30GM50-E2-V1-3G-3D
| Statements of compliance | Certificate No. | File Type | File Size |
|---|---|---|---|
| EU-Declaration of conformity / EU-Konformitätserklärung | DOC-4110 | 345 KB | |
| Certificates | |||
| Canada USA UL Ordinary Location | 20190220-E87056 | 406 KB | |
| Europe Pepperl+Fuchs ATEX Category 3 D Certificate | PF15CERT3774X | 1001 KB | |
| Europe Pepperl+Fuchs ATEX Category 3 G Certificate | PF15CERT3754X | 1015 KB | |
Pepperl+Fuchs AG
Lilienthalstraße 200
68307 Mannheim
Germany
info@de.pepperl-fuchs.com
+49 621 776-0
© 2019 All Rights Reserved.
Pepperl+Fuchs is a leading developer and manufacturer of electronic sensors and components for the global automation market. Continuous innovation, enduring quality, and steady growth have been the foundation of our success for more than 70 years. Pepperl+Fuchs employs 6,200 people worldwide and has manufacturing facilities in Germany, USA, Singapore, Hungary, Indonesia and Vietnam, most of them ISO 9001 certified.