Serviceline Industrial Sensors
Serviceline Explosion Protection
Digital Input LB1001A
- 2 channels
- Dry contact or NAMUR inputs
- Installation in Zone 2 or safe area
- Galvanic isolation between channels and the bus
- Positive or negative logic selectable
- Simulation mode for service operations (forcing)
- Line fault detection (LFD)
- Permanently self-monitoring
- Module can be exchanged under voltage
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH, also apply to Pepperl+Fuchs AG.
Download the complete datasheet as a PDF:
Datasheet excerpt: Technical data of LB1001A
| Slots | ||
|---|---|---|
| Occupied slots | 1 | |
| Supply | ||
| Connection | backplane bus | |
| Rated voltage | 12 V DC , only in connection with the power supplies LB9*** | |
| Power dissipation | 0.65 W | |
| Power consumption | 0.65 W | |
| Internal bus | ||
| Connection | backplane bus | |
| Interface | manufacturer-specific bus to standard com unit | |
| Digital input | ||
| Number of channels | 2 | |
| Sensor interface | ||
| Connection | NAMUR sensor | |
| Connection [2] | volt-free contact | |
| Connection | channel I: 1+, 2/3-; channel II: 4+, 5/6- | |
| Rated values | acc. to EN 60947-5-6 (NAMUR) | |
| Switching point/switching hysteresis | 1.2 ... 2.1 mA / ± 0.2 mA | |
| Voltage | 8.2 V | |
| Internal resistor | 1 kΩ | |
| Line fault detection | can be switched on/off for each channel via configuration tool | |
| Connection | mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring | |
| Short-circuit | < 360 Ω | |
| Open-circuit | < 0.35 mA | |
| Minimum pulse duration | 20 ms | |
| Indicators/settings | ||
| LED indication | Power LED (P) green: supply Status LED (1, 3) red: line fault (per channel) Status LED (2, 4) yellow: signal (per channel) |
|
| Coding | optional mechanical coding via front socket | |
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | EN 61326-1 | |
| Conformity | ||
| Electromagnetic compatibility | NE 21 | |
| Degree of protection | IEC 60529 | |
| Environmental test | EN 60068-2-14 | |
| Shock resistance | EN 60068-2-27 | |
| Vibration resistance | EN 60068-2-6 | |
| Damaging gas | EN 60068-2-42 | |
| Relative humidity | EN 60068-2-56 | |
| Ambient conditions | ||
| Ambient temperature | -20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex) | |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) | |
| Relative humidity | 95 % non-condensing | |
| Shock resistance | shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18 | |
| Vibration resistance | frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance |
|
| Damaging gas | designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3 | |
| Mechanical specifications | ||
| Degree of protection | IP20 when mounted on backplane | |
| Connection | removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm2) or screw terminals (0.08 ... 1.5 mm2) |
|
| Mass | approx. 110 g | |
| Dimensions | 16 x 100 x 102 mm (0.63 x 3.9 x 4 inch) | |
| Data for application in connection with hazardous areas | ||
| Certificate | PF 08 CERT 1234 X | |
| Marking |  II 3 G Ex nA [ic] IIC T4 Gc |
|
| Galvanic isolation | ||
| Input/power supply, internal bus | safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V | |
| Directive conformity | ||
| Directive 2014/34/EU | EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 |
|
| International approvals | ||
| IECEx approval | BVS 09.0037X | |
| Approved for | Ex nA [ic] IIC T4 Gc |
|
| Marine approval | ||
| Lloyd Register | 15/20021 | |
| DNV GL Marine | TAA0000034 | |
| Bureau Veritas Marine | 22449/B0 BV | |
| General information | ||
| System information | The module has to be mounted in appropriate backplanes (LB9***) in Zone 2 or outside hazardous areas. Here, observe the corresponding declaration of conformity. For use in hazardous areas (e. g. Zone 2 or Zone 22) the module must be installed in an appropriate enclosure. |
|
| Supplementary information | EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com. | |
Documents: LB1001A
| Manuals | Language | File Type | File Size |
|---|---|---|---|
| Manual LB Hardware | ENG | 6465 KB | |
| Handbuch LB-Hardware | GER | 3892 KB | |
| Instruction manuals | |||
| Инструкции | BUL | 145 KB | |
| Návod k poużití | CZE | 140 KB | |
| Instruktions manual | DAN | 139 KB | |
| Instruction manual | ENG | 147 KB | |
| Kasutusjuhend | EST | 134 KB | |
| Käyttöohje | FIN | 134 KB | |
| Manuel d'instructions | FRA | 143 KB | |
| Betriebsanleitung | GER | 147 KB | |
| Οδηγίες χρήσης | GRE | 151 KB | |
| Handleiding | HOL | 140 KB | |
| Instruction manual / Betriebsanleitung | HRV | 138 KB | |
| Használati útmutató | HUN | 142 KB | |
| Manuale di istruzioni | ITA | 140 KB | |
| Lietošanas pamācība | LAV | 138 KB | |
| Instrukciju vadovas | LIT | 140 KB | |
| Instrukcja obsługi | POL | 142 KB | |
| Manual de instruções | POR | 141 KB | |
| Manual de utilizare | RON | 139 KB | |
| Návod na poużitie | SLK | 140 KB | |
| Navodila za uporabo | SLV | 137 KB | |
| Manual de instrucciones | SPA | 141 KB | |
| Manual | SWE | 137 KB | |
CAD+CAE: LB1001A
| CAD | File Type | File Size | |
|---|---|---|---|
| 3-D model in IGS format / 3-D-Modell im IGS-Format | IGS | 4128 KB | |
| 3-D model in STP format / 3-D-Modell im STP-Format | STP | 1453 KB | |
| CAD Portal / CAD Portal | LINK | --- | |
| EPLAN | |||
| EPLAN Data Portal / EPLAN Data Portal | LINK | --- | |
| ePLAN-Makros LB-System / ePLAN-Makros LB-System | ZIP | 65808 KB | |
Approvals+Certificates: LB1001A
| Statements of compliance | Certificate No. | File Type | File Size |
|---|---|---|---|
| EU-Declaration of conformity / EU-Konformitätserklärung | DOC-1062D | 234 KB | |
| Certificates | |||
| American Bureau of Shipping (ABS) Marine | 15-HG1450280-PDA | 1468 KB | |
| Brasil TUV Rheinland Brazil | TÜV13.1128X | 938 KB | |
| Bureau Veritas (Maritime) Marine | 22449/B0 BV | 287 KB | |
| DEKRA EXAM IECEx Certificate of Conformity | IECEx BVS 09.0037X | LINK | --- |
| DNV GL Marine | TAA0000034 | 90 KB | |
| EAC NANIO "CCVE" EAC TP TC 012/2011 | RU C-DE.AA87.B.01017 | 5859 KB | |
| Europe Pepperl+Fuchs ATEX Category 3 G Certificate of Conformity | PF 08 CERT 1234 X | 1503 KB | |
| Lloyd's Register Marine | 15/20021 | 2013 KB | |
The new, Zone 2, Class I/Div. 2 certified remote I/O PROFINET gateway from Pepperl+Fuchs opens the door for Industry 4.0 applications in process industries.
Pepperl+Fuchs AG
Lilienthalstraße 200
68307 Mannheim
Germany
info@de.pepperl-fuchs.com
+49 621 776-0
© 2020 All Rights Reserved.
Pepperl+Fuchs is a leading developer and manufacturer of electronic sensors and components for the global automation market. Continuous innovation, enduring quality, and steady growth have been the foundation of our success for more than 70 years. Pepperl+Fuchs employs 6,200 people worldwide and has manufacturing facilities in Germany, USA, Singapore, Hungary, Indonesia and Vietnam, most of them ISO 9001 certified.