Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Download the complete datasheet as a PDF:
Slots | ||
---|---|---|
Occupied slots | 1 | |
Supply | ||
Connection | backplane bus | |
Rated voltage | Use only in connection with the power supplies LB9*** | |
Power dissipation | 1.7 W | |
Power consumption | 2.7 W | |
Internal bus | ||
Connection | backplane bus | |
Interface | manufacturer-specific bus to standard com unit | |
Digital output | ||
Number of channels | 2 | |
Suitable field devices | ||
Field device | Solenoid Valve | |
Field device [2] | audible alarm | |
Field device [3] | visual alarm | |
Connection | channel I: 1+, 4/5/6/8-; channel II: 7+, 4/5/6/8- | |
Current limit | 50 mA both channels parallel 100 mA | |
Internal resistor | 131 Ω , both channels parallel 66 Ω | |
Open loop voltage | 16.5 V , both channels parallel 16.5 V | |
Line fault detection | can be switched on/off for each channel via configuration tool also when turned off (every 2.5 s the valve is turned on for 2 ms) | |
Short-circuit | < 50 Ω | |
Open-circuit | > 10 kΩ | |
Response time | 10 ms (depending on bus cycle time) | |
Watchdog | within 0.5 s the device goes in safe state, e.g. after loss of communication | |
Indicators/settings | ||
LED indication | Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1, 2) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Mode LED (M) white: Parallel operation of outputs |
|
Coding | optional mechanical coding via front socket | |
Directive conformity | ||
Electromagnetic compatibility | ||
Directive 2014/30/EU | EN 61326-1 | |
Conformity | ||
Electromagnetic compatibility | NE 21 | |
Degree of protection | IEC 60529 | |
Environmental test | EN 60068-2-14 | |
Shock resistance | EN 60068-2-27 | |
Vibration resistance | EN 60068-2-6 | |
Damaging gas | EN 60068-2-42 | |
Relative humidity | EN 60068-2-56 | |
Ambient conditions | ||
Ambient temperature | -20 ... 60 °C (-4 ... 140 °F) | |
Storage temperature | -25 ... 85 °C (-13 ... 185 °F) | |
Relative humidity | 95 % non-condensing | |
Shock resistance | shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18 | |
Vibration resistance | frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance |
|
Damaging gas | designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3 | |
Mechanical specifications | ||
Degree of protection | IP20 when mounted on backplane | |
Connection | removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm2) or screw terminals (0.08 ... 1.5 mm2) |
|
Mass | approx. 150 g | |
Dimensions | 16 x 100 x 102 mm (0.63 x 3.9 x 4 inch) | |
Data for application in connection with hazardous areas | ||
EU-type examination certificate | EXA 16 ATEX 0025X | |
Marking | ![]() ![]() I (M1) [Ex ia Ma] I |
|
Output | ||
Voltage | 17.8 V | |
Current | 162 mA | |
Power | 721 mW | |
Internal capacitance | 12 nF | |
Internal inductance | 0 mH | |
Output (both channels parallel) | ||
Voltage | 17.8 V | |
Current | 324 mA | |
Power | 1442 mW | |
Internal capacitance | 24 nF | |
Internal inductance | 0 mH | |
Galvanic isolation | ||
Output/power supply, internal bus | safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V | |
Directive conformity | ||
Directive 2014/34/EU | EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 61241-11:2006 |
|
International approvals | ||
ATEX approval | EXA 16 ATEX 0025X | |
General information | ||
System information | The module has to be mounted in appropriate backplanes (LB9***) in Zone 2 or outside hazardous areas. Here, observe the corresponding declaration of conformity. For use in hazardous areas (e. g. Zone 2, Zone 22 or Div. 2) the module must be installed in an appropriate enclosure. |
|
Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
Manuals | Language | File Type | File Size |
---|---|---|---|
Functional Safety Manual | ENG | 974 KB | |
Manual | ENG | 3636 KB | |
Handbuch | GER | 3662 KB | |
Handbuch Funktionale Sicherheit | GER | 978 KB | |
Instruction manuals | |||
Инструкции | BUL | 0 KB | |
Návod k poużití | CZE | 141 KB | |
Instruktions manual | DAN | 140 KB | |
Instruction manual | ENG | 148 KB | |
Kasutusjuhend | EST | 135 KB | |
Käyttöohje | FIN | 135 KB | |
Manuel d'instructions | FRA | 149 KB | |
Betriebsanleitung | GER | 149 KB | |
Οδηγίες χρήσης | GRE | 0 KB | |
Handleiding | HOL | 141 KB | |
Instruction manual / Betriebsanleitung | HRV | 140 KB | |
Használati útmutató | HUN | 0 KB | |
Manuale di istruzioni | ITA | 146 KB | |
Lietošanas pamācība | LAV | 139 KB | |
Instrukciju vadovas | LIT | 140 KB | |
Instrukcja obsługi | POL | 144 KB | |
Manual de instruções | POR | 143 KB | |
Manual de utilizare | RON | 141 KB | |
Návod na poużitie | SLK | 142 KB | |
Navodila za uporabo | SLV | 138 KB | |
Manual de instrucciones | SPA | 147 KB | |
Manual | SWE | 138 KB | |
Product information | |||
Product information | ENG | 189 KB | |
Produktinformation | GER | 243 KB |
Statements of compliance | Certificate No. | File Type | File Size |
---|---|---|---|
EU-Declaration of Conformity / EU-Konformitätserklärung | DOC-2602A | 235 KB | |
Certificates | |||
China NEPSI | GYJ 18.1109X | 4865 KB | |
EAC NANIO "CCVE" EAC TP TC 012/2011 | RU C-DE.AA87.B.01017 | 5859 KB | |
EXA Ex i and Ex n | IECEx EXA 16.0010X | LINK | --- |
Europe EXA ATEX Category (1) D ATEX Category 3 G | EXA 16 ATEX 0025X | 366 KB | |
USA Canada, USA UL Certificate of Compliance cULus | CoC 20150604 - E106378 RepRef 20140227 | 570 KB | |
Control drawings | |||
Control drawing UL, CUL / Control drawing UL, cUL | 320 KB |
The digital output features 2 independent channels.
The device can be used to drive solenoids, sounders, or LEDs.
Open and short circuit line faults are detected in on and off state.
The outputs are galvanically isolated from the bus and the power supply.
The output can be switched off via a contact. This can be used for bus-independent safety applications.