Bus Coupler ISCM8100
- Com unit for 80 analog or 184 digital channels
- HART communication via the bus
- Device installation in Zone 2 or Zone 22
- Configuration via I/A system user interface
- Nonvolatile memory for configuration and parameter settings
- Self configuration in redundant systems
- Outputs drive to safe state in case of failures
- Supports single and multichannel I/O modules
- ON/OFF delay for digital inputs (filter, pulse extension)
- Quick communication set-up
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Download the complete datasheet as a PDF:
Datasheet excerpt: Technical data of ISCM8100
| Supply | ||
|---|---|---|
| Connection | backplane bus | |
| Rated voltage | 5 V DC , only in connection with the power supplies FB92** | |
| Power consumption | 2 W | |
| Interface | ||
| Connection | HDLC via terminals on backplane | |
| Station connection | directly to PCS | |
| Bus length | max. 150 m (500 feet) | |
| Internal bus | ||
| Connection | backplane bus | |
| Service interface | ||
| Connection | 8-pin connector to be used in case of maintenance via safety barrier |
|
| Indicators/settings | ||
| LED indication | LED green: supply LED red: fault LED yellow: communication status |
|
| Labeling | space for labeling at the front | |
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | EN 61326-1 | |
| Conformity | ||
| Electromagnetic compatibility | NE 21 | |
| Degree of protection | IEC 60529 | |
| Fieldbus standard | HDLC via terminals on backplane | |
| Environmental test | HDLC to ISO 13239 | |
| Shock resistance | EN 60068-2-27 | |
| Vibration resistance | EN 60068-2-6 | |
| Damaging gas | EN 60068-2-42 | |
| Relative humidity | EN 60068-2-56 | |
| Ambient conditions | ||
| Ambient temperature | -20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex) | |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) | |
| Relative humidity | 95 % non-condensing | |
| Shock resistance | shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18 | |
| Vibration resistance | frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance |
|
| Damaging gas | for plugs: 21 days in 25 ppm SO2, at 25 °C and 75 % rel. humidity, device G3 | |
| Mechanical specifications | ||
| Degree of protection | IP20 (module) , mounted on backplane | |
| Connection | device plug (accessories) front connector for letterbug and service bus |
|
| Mass | 150 g | |
| Dimensions | 32 x 100 x 103 mm (1.26 x 3.9 x 4 inch) | |
| Height | 100 mm | |
| Width | 32 mm | |
| Length | 103 mm | |
| Data for application in connection with hazardous areas | ||
| Supply | only in connection with the power supplies LB9*** | |
| Certificate | PF 08 CERT 1234 | |
| Marking |  II 3 G Ex nA IIC T4 |
|
| Directive conformity | ||
| Directive 2014/34/EU | EN 60079-0 , EN 60079-1 , EN 60079-11 | |
| International approvals | ||
| UL approval | QUZW7.E106378 | |
| IECEx approval | BVS 08.0011X | |
| General information | ||
| System information | The module has to be mounted in appropriate backplanes (LB9***) in Zone 2 or outside hazardous areas. Here, observe the corresponding declaration of conformity. For use in hazardous areas (e. g. Zone 2 or Zone 22) the module must be installed in an appropriate enclosure. |
|
| Supplementary information | EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com. | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27210121 |
| ECLASS 12.0 | 27210121 |
| ECLASS 11.0 | 27210121 |
| ECLASS 10.0.1 | 27210121 |
| ECLASS 9.0 | 27210121 |
| ECLASS 8.0 | 27210121 |
| ECLASS 5.1 | 27210121 |
| ETIM 9.0 | EC001485 |
| ETIM 8.0 | EC001485 |
| ETIM 7.0 | EC001485 |
| ETIM 6.0 | EC001485 |
| ETIM 5.0 | EC001485 |
| UNSPSC 12.1 | 39121008 |
Details: ISCM8100
Function
The ISCM Remote I/O ComUnit or gateway brings intrinsically safe inputs and outputs from sensors and actuators to the Foxboro Invensys HDLC bus.
It makes use of all the regular I/O modules and thus transports signals to and from NAMUR and switch type inputs and high power IS solenoids or even power relays. The system supplies 4 mA to 20 mA transmitters and accepts input from 20 mA current sources or temperature sensors. It drives I/P converters and proportional valves and positioners.
The HDLC hardware is familiar to Invensys I/A series users. Autoconfiguration ensures that modules register with the host as soon as they are inserted. There is no extra configuration required.
The system makes use of regular I/A series function blocks behaving like any ordinary FBM.
Approvals: ISCM8100
| Certificates | Certificate No. | Language | File Type | File Size |
|---|---|---|---|---|
| DEKRA EXAM IECEx Certificate of Conformity | IECEx BVS 09.0037X | ALL | LINK | --- |
| DNV Marine | TAA0000034 | ALL | 110 KB | |
| Lloyd's Register Marine | LR2003616TA-02 | ALL | 557 KB | |
| South Africa MASC | MASC MS/20-8438X | ALL | 730 KB |
Associated Products: ISCM8100
| Accessories | ||||||
|---|---|---|---|---|---|---|
|
||||||
The new LB/FB PROFINET gateways from Pepperl+Fuchs open the door for IIoT 4.0 applications in process industries.
Pepperl+Fuchs SE
Lilienthalstraße 200
68307 Mannheim
Germany
info@de.pepperl-fuchs.com
+49 621 776-0
Pepperl+Fuchs is a leading developer and manufacturer of electronic sensors and components for the global automation market. Continuous innovation, enduring quality, and steady growth have been the foundation of our success for more than 70 years. Pepperl+Fuchs employs 6,300 people worldwide and has manufacturing facilities in Germany, USA, Singapore, Hungary, Indonesia and Vietnam, most of them ISO 9001 certified.