Serviceline Industrial Sensors
Serviceline Explosion Protection
Power Supply PS1000-A9-24.40-IO
- 380 V AC to 480 V AC wide-range inputs
- Output 24 V DC, 40 A, 960 W, 3-phase
- Housing width 110 mm
- Efficiency up to 95.3 %
- Minimal inrush current surge
- IO-Link interface
- Current sharing for parallel use
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Download the complete datasheet as a PDF:
Datasheet excerpt: Technical data of PS1000-A9-24.40-IO
| Memory | ||
|---|---|---|
| Type/Size | 8 kBit EEPROM | |
| Electrical specifications | ||
| Efficiency | 95.3 % at 3 x 400 V AC 95.2 % at 3 x 480 V AC |
|
| Power dissipation | 47.3 W at 3 x 400 V AC 48.4 W at 3 x 480 V AC |
|
| Interface | ||
| Interface type | IO-Link | |
| Device profile | Identification and Diagnosis - I&D | |
| Process data | Input 6 Byte - input voltage 16 Bit - output voltage 16 Bit - output current 16 Bit |
|
| Vendor ID | 1 (0x0001) | |
| Device ID | 999425 (0x0F4001) | |
| Transfer rate | COM2 (38.4 kBit/s) | |
| Min. cycle time | 2 ms | |
| SIO mode support | no | |
| Compatible master port type | Class A , Class B | |
| Current consumption | max. 90 mA | |
| Voltage range | 18 ... 30 V | |
| Input | ||
| Voltage range | 3x 380 ... 480 V AC (-15 %/+20 %), 50 ... 60 Hz (±6 %) | |
| Current | 1.65 A at 3 x 400 V AC 1.35 A at 3 x 480 V AC for lower output currents see technical information |
|
| Inrush current | 4.5 A peak at 3 x 400 V AC, temperature-independent 4.5 A peak at 3 x 480 V AC , temperature-independent |
|
| Capacity factor | 0.88 at 3 x 400 V AC 0.9 at 3 x 480 V AC |
|
| Output | ||
| Rated voltage | 24 V DC | |
| Voltage range | 24 ... 28.5 V DC hardware limitation via potentiometer 15 ... 28 V DC via IO-Link factory setting: 24.1 V |
|
| Rated current | 40 A | |
| Current | continuous: 40 ... 33.7 A at ambient temperature < 55 °C (131 °F) 27.5 ... 23.4 A at ambient temperature 70 °C (158 °F) short-term up to 5 s: 60 ... 50.5 A at ambient temperature < 70 °C (158 °F) linear power derating see technical information |
|
| Power | 960 W | |
| Ripple | max. 100 mV pp | |
| Hold-up time | 25 ms at 3 x 400 V AC 25 ms at 3 x 480 V AC |
|
| Overload behavior | constant current mode | |
| Short-circuit current | typ. 46 A continuous, load impedance < 10 mΩ | |
| Voltage limitation | typ. 30.5 V DC max. 32 V DC |
|
| Galvanic isolation | ||
| Input/Output | SELV/PELV | |
| Indicators/settings | ||
| Display elements | LED green: status DC OK - LED lights up if the output voltage is > 90 % of the adjusted output voltage LED red: overload - LED lights up if the output voltage is < 90 % of the adjusted output voltage or in case of short circuit - flashes if the shutdown has been activated or if the device has shut down due to overtemperature IO-Link communication, LED green/red: LED green: - LED flashes if the communication is active - LED lights up if IO-Link is powered - LED is off if IO-Link is not powered LED red: - LED lights up if an IO-Link event is present - LED is off if no IO-Link event is present or at DC OK |
|
| Configuration | configuration via IO-Link - output voltage adjustment - operating mode adjustment - shutdown input adjustment |
|
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | IEC/EN 61000-6-1 , IEC/EN 61000-6-2 , IEC/EN 61000-6-3 , IEC/EN 61000-6-4 , IEC/EN 61000-3-2 , IEC/EN 61000-3-3 |
|
| Low voltage | ||
| Directive 2014/35/EU | EN 61010-1 | |
| RoHS | ||
| Directive 2011/65/EU (RoHS) | IEC/EN 63000:2019 | |
| Conformity | ||
| Degree of protection | EN 60529 | |
| Communication interface | IEC 61131-9 / IO-Link V1.1.2 | |
| Shock resistance | EN 60068-2-27 | |
| Vibration resistance | EN 60068-2-6 | |
| Ambient conditions | ||
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) , see technical information | |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Relative humidity | 5 ... 95 %, noncondensing | |
| Shock resistance | 15 g , 6 ms or 10 g , 11 ms | |
| Vibration resistance | 2 ... 17.8 Hz : ± 1.6 mm , 17.8 ... 500 Hz : 1 g | |
| Mechanical specifications | ||
| Housing material | aluminum alloy , galvanized steel | |
| Degree of protection | IP20 | |
| Connection | ||
| Input | screw terminals conductor cross section: max. 6 mm2 (AWG 20-10) cable diameter: max. 2.8 mm, wire end ferrules included stripped insulation length: 7 mm tightening torque: max. 1 Nm |
|
| Output | screw terminals conductor cross section: max. 16 mm2 (AWG 22-8) cable diameter: max. 5.2 mm, wire end ferrules included stripped insulation length: 12 mm tightening torque: max. 2.3 Nm |
|
| Mass | approx. 1500 g | |
| Dimensions | 110 x 124 x 143.5 mm (W x H x D) , without DIN mounting rail | |
| Height | 124 mm | |
| Width | 110 mm | |
| Depth | 143.5 mm | |
| Mounting | on 35 mm DIN mounting rail acc. to EN 60715:2001 | |
| International approvals | ||
| UL approval | E223176 | |
| General information | ||
| Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27040790 |
| ECLASS 12.0 | 27040790 |
| ECLASS 11.0 | 27040790 |
| ECLASS 10.0.1 | 27040790 |
| ECLASS 9.0 | 27040790 |
| ECLASS 8.0 | 27049090 |
| ECLASS 5.1 | 27049090 |
| ETIM 9.0 | EC002542 |
| ETIM 8.0 | EC002542 |
| ETIM 7.0 | EC002542 |
| ETIM 6.0 | EC002542 |
| ETIM 5.0 | EC002542 |
| UNSPSC 12.1 | 39121004 |
Details: PS1000-A9-24.40-IO
Function
The device is used to supply field devices with 24 V DC and 40 A.
The device has a large power reserve of 150 % for up to 5 s to support the starting of heavy loads such as DC motors or capacitive loads.
The device is equipped with an IO-Link interface V1.1 to configure and parameterize the device and access data.
Communication status, device status and overload are indicated by LEDs.
The device has a relay contact output for remote monitoring.
The device is mounted on a 35 mm DIN mounting rail according to EN 60715.
Product Documentation: PS1000-A9-24.40-IO
| Product information | Language | File Type | File Size |
|---|---|---|---|
| Technical information | ENG | 2963 KB | |
| Safety and Security Documentation | |||
| Instruction manual / Betriebsanleitung | ALL | 432 KB | |
| Parameter Information | |||
| Parameterdatenblatt | ENG | 684 KB | |
Design / Simulation: PS1000-A9-24.40-IO
| CAD | Language | File Type | File Size |
|---|---|---|---|
| CAD 3-D / CAD 3-D | ALL | STP | 8733 KB |
| CAD Portal / CAD Portal | ALL | LINK | --- |
| CAE | |||
| CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ | ALL | EDZ | 207 KB |
Approvals: PS1000-A9-24.40-IO
| Certificates | Certificate No. | Language | File Type | File Size |
|---|---|---|---|---|
| IO-Link Manufacturer Declaration | CERT-6082 | ALL | 55 KB | |
| US CA UL | CoC E223176 RptRef E223176-20070416 | ALL | 444 KB | |
| Declaration of Conformity | ||||
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | DOC-4792 | ALL | 79 KB | |
Software: PS1000-A9-24.40-IO
| Device Description Files/Drivers | Release Info | File Type | File Size |
|---|---|---|---|
| IODD for PS1000-A9-24.40-IO / IODD für PS1000-A9-24.40-IO | V1.00.000 / 2021-10-15 | ZIP | 282 KB |
Pepperl+Fuchs SE
Lilienthalstraße 200
68307 Mannheim
Germany
info@de.pepperl-fuchs.com
+49 621 776-0
© 2024 All Rights Reserved.
Pepperl+Fuchs is a leading developer and manufacturer of electronic sensors and components for the global automation market. Continuous innovation, enduring quality, and steady growth have been the foundation of our success for more than 70 years. Pepperl+Fuchs employs 6,300 people worldwide and has manufacturing facilities in Germany, USA, Singapore, Hungary, Indonesia and Vietnam, most of them ISO 9001 certified.