Termination Board HiDTB08-SCT-99C-SC-RA

Datasheet excerpt: Technical data of  HiDTB08-SCT-99C-SC-RA

Supply
Connection		X20: terminals 3, 5(+); 4, 6(-)
Nominal voltage		24 V DC , in consideration of rated voltage of used isolators
Voltage drop		0.9 V , voltage drop across the series diode on the termination board must be considered
Ripple		≤ 10 %
Fusing		2 A , in each case for 8 modules
Power dissipation		≤ 500 mW , without modules
Reverse polarity protection		yes
Redundancy
Supply		Redundancy available. The supply for the isolators is decoupled, monitored and fused.
Fault indication output
Connection		X20: terminals 1, 2
Output type		volt-free contact
Switch behaviour		no fault: relay contact closed power supply fault: relay contact open module fault: relay contact open
Contact loading		30 V DC, 1 A
Indicators/settings
Display elements		LED PWR1 (termination board power supply), green LED LED PWR2 (termination board power supply), green LED LED FAULT (fault indication), red LED - LED lits: module fault - LED flashes: power supply fault
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Conformity
Electromagnetic compatibility		NE 21:2017 For further information see system description.
Degree of protection		IEC 60529:2001
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-40 ... 70 °C (-40 ... 158 °F)
Mechanical specifications
Degree of protection		IP20
Connection
	Field side	explosion hazardous area: 9 screw terminals per module , blue
	Control side	non-explosion hazardous area: 9 screw terminals per module , black
	Supply	pluggable screw terminals , black
	Fault output	pluggable screw terminals , black
Core cross-section		screw terminals: 0.25 ... 1.5 mm2 (24 ... 12 AWG)
Material		housing: polycarbonate, 10 % glass fiber reinforced
Mass		approx. 740 g
Dimensions		150 x 200 x 163 mm (5.9 x 7.9 x 6.42 inch) , height including module assembly
Mounting		on 35 mm DIN mounting rail acc. to EN 60715:2001
Data for application in connection with hazardous areas
EU-type examination certificate		CESI 11 ATEX 062
	Marking	II (1)G [Ex ia Ga] IIC II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I
Non-hazardous area
	Maximum safe voltage	250 V (Attention! Um is no rated voltage.)
Galvanic isolation
	Field circuit/control circuit	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 50303:2000
International approvals
CSA approval
	Control drawing	see control drawing of correspoding modules
IECEx approval
	IECEx certificate	IECEx CES 11.0022
	IECEx marking	[Ex ia Ga] IIC [Ex ia Da] IIIC [Ex ia Ma] I
General information
Supplementary information		Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Accessories
Designation		- HART communication board for 1-channel modules: HiATB01-HART-4X8-Y1 - HART communication board for 2-channel modules: HiATB01-HART-2X16

Documents: HiDTB08-SCT-99C-SC-RA

CAD+CAE: HiDTB08-SCT-99C-SC-RA

Approvals+Certificates: HiDTB08-SCT-99C-SC-RA

Associated Products: HiDTB08-SCT-99C-SC-RA

Accessories
HiATB01-HART-2X16 HART Communication Board 2 x 16-channel, 24 V DC supply, Suitable for HART communication, Dual RS 485 connections, Used with HiD/HiC Termination Boards, LED indicator for supply statuspa
HiDMux2700 HART Multiplexer Master 32-channel, 24 V DC supply, HART field device input (revision 5 to 7), RS-485 interface, Up to SIL 3 acc. to IEC 61508pa
HiATB01-HART-4X8-Y1 HART Communication Board 4 x 8-channel, 24 V DC supply, Suitable for HART communication, Dual RS 485 connections, Used with HiD/HiC Termination Boards, LED for supply statuspa
H-CJC-SC-8 Resistance Thermometer for Cold Junction Compensation For Cold Junction Compensation of HiD2081, HiD2082, For H-System Termination Boards, For terminal blocks with screw terminals, Packaging unit: 8 piecespa
HiACA-UNI-FLK34-FLK34-0M5 HART Connection Cable H-System accessory, Connection cable between HART Communication Board and Termination Board, 34-pin cablepa
HIACA-UNI-FLK34-FLK34-1M0 HART Connection Cable H-System accessory, Connection cable between HART Communication Board and Termination Board, 34-pin cablepa
HiACA-UNI-FLK34-FLK34-2M0 HART Connection Cable H-System accessory, Connection cable between HART Communication Board and Termination Board, 34-pin cablepa
HiACA-UNI-FLK34-FLK34-3M0 HART Connection Cable H-System accessory, Connection cable between HART Communication Board and Termination Board, 34-pin cablepa
HiACA-UNI-FLK34-FLK34-6M0 HART Connection Cable H-System accessory, Connection cable between HART Communication Board and Termination Board, 34-pin cablepa
HiALC-HiDTB-SET-150 Label Carrier For HiD Termination Boards, 1 piece for 8-position Termination Board, 2 pieces for 16-position Termination Boardpa

Function: HiDTB08-SCT-99C-SC-RA

The termination board has 8 plug-in slots for isolators. Any isolator can be inserted into any slot, enabling a mixture of I/O types on one termination board.

The termination board features fixed screw terminals for the field side connection and for the control side connection along with a HART cordset for interconnection to a separate HART Communication Board.

Information about missing supply voltage of the isolators is available for the system as volt-free contact at the redundant power supply terminals.

Wiring errors from field side will be reported via the same relay contact, if this function supported by the the isolators.

The termination board is supplied with a robust plastic housing as standard. This design permits the fast and reliable installation on 35 mm DIN mounting rail acc. to EN 60715 in the cabinet.