Línea de servicio de Sensores Industriales
Atención al cliente para protección contra explosiones

Float Switch LFL2-**-U

LFL2-**-U
  • Switch element: microswitch, mercury-free
  • Limit value detection for fluids
  • Sleeve design: small diameter, mounting through G1 tap hole possible
  • Ball design: high buoyancy

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Descargue la hoja de datos completa en PDF:


Extracto de la hoja de datos: Información técnica del  LFL2-**-U

General specifications
Construction typemicroswitch with switching ball, change-over contact
SeriesLFL2-**-U
Electrical specifications
Contact loading250 V AC/3 A; 150 V DC/0.25 A resistive load; 60 V DC/1 A resistive load
Rated insulation voltage300 V
Pulse withstand voltage4 kV
Electrical life≥ 5 x 104 switching cycles
Output
Connectionvolt-free change-over contact
Directive conformity
Low voltage
Directive 2014/35/EUEN 60947-5-1:2017
Conformity
Degree of protectionIEC 60529:2001
Function and system design
Equipment architectureThis device may be used with any sequential circuit, as long as the circuit can support the electrical circuit values of the switching elements.
Operating conditions
Installation conditions
Installation instructionsrange of application and minimum length between mounting and float:
- PVC version: ≥ 50 mm (2 inch), preferred for water
- PUR version: ≥ 100 mm (4 inch), preferred for fuels, heating oils, oily fluids
- CSM/CM version: ≥ 100 mm (4 inch), preferred for many acids and lyes
- TPK version: ≥ 100 mm (4 inch), preferred for many acids and lyes

mounting:
- The float switch is mounted either from sidewards through a cable gland ≥ G1A into the vessel or
- by means of a counter weight or rods (e. g. float switch combination) from the top.
The pivot of the cable should always be horizontal.
Process conditions
Process pressure (static pressure)sleeve design: ≤ 3 bar at 20 °C (68 °F)
ball design: ≤ 2 bar at 20 °C (68 °F)
Densitysleeve design: ≥ 0.8 g/cm3
ball design: ≥ 0.6 g/cm3
Ambient conditions
Ambient temperaturePVC version: 5 ... 70 °C (41 ... 158 °F)
PUR version: 5 ... 70 °C (41 ... 158 °F)
CSM/CM version: -20 ... 70 °C (-4 ... 158 °F)
TPK version: 5 ... 70 °C (41 ... 158 °F)
Storage temperature-25 ... 70 °C (-13 ... 158 °F)
Altitude≤ 2000 m above MSL
Mechanical specifications
Degree of protectionIP68
Mechanical construction
Materialfloat: PP (Polypropylene)
cable:
- PVC version: PVC cable, highly flexible (3 x 0.75 mm2)
- PUR version: PUR cable, highly flexible (3 x 0.50 mm2)
- CSM/CM version: CSM/CM cable (chlorinated polyethylene, (3 x 0.75 mm2))
- TPK version: TPK cable, (3 x 0.75 mm2)
Switching pointswitch angle, measured against the horizontal:
- upper switch point +25° ±10°
- lower switch point -14° ±10°
General information
Supplementary informationObserve the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Accessories
Designation- LFL-Z231, counter nut, G1A, PVC
- LFL-Z32, counter weight, grey cast iron with plastic coating (Polycarbonate)
- LFL-Z33, counter weight, grey cast iron with ECTFE coating (Halar)
- LFL-Z131, gland screw connection G1A, PVC
- LFL-Z132, gland screw connection G1A, brass
- LFL-Z161, gland screw connection G2A, PVC
- LFL-Z431, gland screw connection 1 NPT, PVC
- LFL-Z461, gland screw connection 2 NPT, PVC

Classifications

SystemClasscode
ECLASS 13.027200510
ECLASS 12.027200510
ECLASS 11.027200510
ECLASS 10.0.127200510
ECLASS 9.027200510
ECLASS 8.027200510
ECLASS 5.127200510
ETIM 9.0EC011178
ETIM 8.0EC011178
ETIM 7.0EC011178
ETIM 6.0EC001447
ETIM 5.0EC001447
UNSPSC 12.141111950

Details: LFL2-**-U

Función

El microconmutador (contacto de conmutación) está integrado en el flotador de PP y se activa en caso de que se produzcan desviaciones de la posición horizontal. La esfera de conmutación del flotador, que se mueve a lo largo de un eje, activa el microconmutador.

Product Documentation: LFL2-**-U

Seleccionar idioma:
Safety and Security DocumentationIdiomaTipo de archivoTamaño
Manual de instruccionesSPAPDF57 KB

Design / Simulation: LFL2-**-U

Seleccionar idioma:
CADIdiomaTipo de archivoTamaño
CAD 3-D / CAD 3-DALLSTP482 KB

Approvals: LFL2-**-U

Seleccionar idioma:
Declaration of ConformityNúmero de CertificadoIdiomaTipo de archivoTamaño
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)DOC-0581CALLPDF72 KB
Contamination Declaration
Contamination declaration / Kontaminationserklärung   ALLPDF137 KB