AS-Interface gateway VBG-CAN-K5-D
- Gateway according to AS-Interface specification 2.1 for up to 62 units
- Protocol standard: CANopen
- Voltage supply from AS-Interface
- Programmable slave addresses
- Display of detected slaves
- Fault diagnosis via LEDs and grafic display
- Easy commissioning by graphic display
- AS-Interface monitor or extended AS-Interface diagnostic read via display
Contact Us
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Download the complete datasheet as a PDF:
Datasheet excerpt: Technical data of VBG-CAN-K5-D
| Product Description |
|---|
| CANopen Gateway |
| General specifications | ||
|---|---|---|
| AS-Interface specification | V2.11 | |
| PLC-Functionality | none | |
| Diagnostics function | Extended function via display | |
| Indicators/operating means | ||
| Display | Graphical LC display for addressing and error messages | |
| LED AS-i ACTIVE | AS-Interface operation normal; LED green | |
| LED CONFIG ERR | configuration error; LED red | |
| LED PRG ENABLE | autom. programming; LED green | |
| LED POWER | voltage ON; LED green | |
| LED PRJ MODE | projecting mode active; LED yellow | |
| LED U AS-i | AS-Interface voltage; LED green | |
| LED MNS | Module/net status; LED green/red | |
| Switch SET | Selection and setting of a slave address | |
| OK button | Mode selection traditional-graphical/confirmation | |
| Button MODE | Mode selection PRJ-operation/save configuration/cursor | |
| ESC button | Mode selection traditional-graphical/cancel | |
| Electrical specifications | ||
| Insulation voltage | ≥ 500 V | |
| Rated operating voltage | from AS-Interface | |
| Rated operating current | ≤ 200 mA | |
| Interface | ||
| Protocol | CANopen | |
| Connection | ||
| AS-Interface | screw terminals | |
| DeviceNet | 5-pin CombiCon connector according to DeviceNet specification | |
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | EN 62026-2:2013 | |
| Standard conformity | ||
| Degree of protection | EN 60529:2000 | |
| AS-Interface | EN 62026-2:2013 | |
| Ambient conditions | ||
| Ambient temperature | 0 ... 55 °C (32 ... 131 °F) | |
| Storage temperature | -15 ... 70 °C (5 ... 158 °F) | |
| Mechanical specifications | ||
| Degree of protection | IP40 (housing), IP20 (terminals) | |
| Mass | 420 g | |
| Construction type | Low profile housing , plastic | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27242607 |
| ECLASS 12.0 | 27242607 |
| ECLASS 11.0 | 27242607 |
| ECLASS 10.0.1 | 27242607 |
| ECLASS 9.0 | 27242607 |
| ECLASS 8.0 | 27242607 |
| ECLASS 5.1 | 27242607 |
| ETIM 9.0 | EC001603 |
| ETIM 8.0 | EC001603 |
| ETIM 7.0 | EC001603 |
| ETIM 6.0 | EC001603 |
| ETIM 5.0 | EC001603 |
| UNSPSC 12.1 | 39121535 |
Details: VBG-CAN-K5-D
Function
The VBG-CAN-K5-D is a gateway to a CANopen network. The gateway acts as a 128 bit digital I/O module. All mandatory functions, as well as interrupts and 8 bit groups etc. are implemented. An emergency message can be activated in the case of an AS-Interface configuration error.
The AS-Interface master is connected to CANopen with a 5-pin CombiCon connector in accordance with the DeviceNet specifications. Self-opening device terminals for leads are available for all other connections. The push buttons are used for address assignment of the AS-Interface slaves and acceptance of the desired configuration. There are 7 LEDs on the front panel, showing the current status of the AS-Interface line.
In the case of the AS-Interface Gateway with graphical display, the AS-Interface circuit can be placed in service and the test of the connected periphery can be kept entirely separate from the commissioning of the DeviceNet. On-site operation with the aid of the graphical display and 4 push buttons makes it possible to show all functions on the display that are covered by the AS-i Control Tools software for other AS-Interface masters.
Product Documentation: VBG-CAN-K5-D
| Manuals | Language | File Type | File Size |
|---|---|---|---|
| Manual VBG-CAN-K5-D | ENG | 3447 KB |
Design / Simulation: VBG-CAN-K5-D
| CAD | Language | File Type | File Size |
|---|---|---|---|
| CAD 3-D / CAD 3-D | ALL | STP | 150 KB |
| CAD Portal / CAD Portal | ALL | LINK | --- |
Approvals: VBG-CAN-K5-D
| Declaration of Conformity | Certificate No. | Language | File Type | File Size |
|---|---|---|---|---|
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | DOC-2449C | ALL | 109 KB |
Software: VBG-CAN-K5-D
| Device Description Files/Drivers | Release Info | File Type | File Size |
|---|---|---|---|
| EDS file VBG-CAN-K5-D / EDS-Datei VBG-CAN-K5-D | 10/2003 | ZIP | 2 KB |
Introduce yourself to the ASi KE5 gateway, IIoT, and the basic working principle of the REST API. The AS-Interface gateways featured in the video are the VBG-EP1-KE5-D and VBG-EP1-KE5-DMD models.
Learn how to change your ASi-3 gateway from the legacy type K20 to the KE5 type.
This free PDF white paper compares the different TCP-based communication protocols (AMQP, OPC UA, MQTT, REST API) that have found their way up and are considered the enablers of IIoT and Industry 4.0. Get your free download now!
Pepperl+Fuchs Inc.
1600 Enterprise Parkway
Twinsburg, OH 44087
United States of America
sales@us.pepperl-fuchs.com
+1 330 425-3555
Pepperl+Fuchs is a leading developer and manufacturer of electronic sensors and components for the global automation market. Continuous innovation, enduring quality, and steady growth have been the foundation of our success for more than 70 years. Pepperl+Fuchs employs 6,300 people worldwide and has manufacturing facilities in Germany, USA, Singapore, Hungary, Indonesia and Vietnam, most of them ISO 9001 certified. Pepperl+Fuchs does not sell personal data.