Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH, also apply to Pepperl+Fuchs AG.
Download the complete datasheet as a PDF:
General specifications | ||
---|---|---|
Signal type | Analog input | |
Functional safety related parameters | ||
Safety Integrity Level (SIL) | SIL 3 | |
Supply | ||
Connection | Power Rail or terminals 9+, 10- | |
Rated voltage | 19 ... 30 V DC | |
Ripple | ≤ 10 % | |
Rated current | ≤ 50 mA | |
Power dissipation | ≤ 800 mW | |
Power consumption | ≤ 1.2 W | |
Input | ||
Connection side | field side | |
Connection | terminals 1+, 2-; 3+, 4- | |
Input signal | 4 ... 20 mA , limited to approx. 27 mA reverse polarity protected | |
Line fault detection | downscaling ≤ 3 mA ; upscaling ≥ 22 mA | |
Voltage drop | approx. 5 V on terminals 3+, 4- | |
Available voltage | ≥ 15 V at 20 mA terminals 1+, 2- | |
Output | ||
Connection side | control side | |
Connection | terminals 5-, 6+ | |
Load | 0 ... 300 Ω (source mode) | |
Output signal | 4 ... 20 mA or 1 ... 5 V (on 250 Ω, 0.1 % internal shunt) 4 ... 20 mA (sink mode), operating voltage 16 ... 28 V |
|
Ripple | 20 mV rms | |
Fault indication output | ||
Output type | fault bus signal , open collector transistor | |
Transfer characteristics | ||
Deviation | at 20 °C (68 °F) ≤ ± 20 µA incl. calibration, linearity, hysteresis, loads and supply voltage fluctuations (source mode and sink mode 4 ... 20 mA) ≤ 10 mV incl. calibration, linearity, hysteresis and fluctuations of supply voltage (source mode 1 ... 5 V) |
|
Influence of ambient temperature | < 2 µA/K (0 ... 70 °C (32 ... 158 °F)); < 4 µA/K (-20 ... 0 °C (-4 ... 32 °F)) (source mode and sink mode 4 ... 20 mA) < 0.5 mV/K (0 ... 70 °C (32 ... 158 °F)); < 1 mV/K (-20 ... 0 °C (-4 ... 32 °F)) (source mode 1 ... 5 V) |
|
Frequency range | field side into the control side: bandwidth with 1 mApp signal 0 ... 3 kHz (-3 dB) control side into the field side: bandwidth with 0.5 Vpp signal 0 ... 3 kHz (-3 dB) |
|
Settling time | ≤ 200 ms | |
Rise time/fall time | ≤ 20 ms | |
Galvanic isolation | ||
Input/Output | safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V | |
Input/power supply | safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V | |
Output/power supply | Basic isolation acc. to EN 61010-1 rated insulation voltage ≤ 50 V | |
Indicators/settings | ||
Display elements | LEDs | |
Control elements | DIP-switch | |
Configuration | via DIP switches | |
Labeling | space for labeling at the front | |
Directive conformity | ||
Electromagnetic compatibility | ||
Directive 2014/30/EU | EN 61326-1:2013 (industrial locations) | |
Conformity | ||
Electromagnetic compatibility | NE 21:2017 For further information see system description. |
|
Degree of protection | IEC 60529:2001 | |
Ambient conditions | ||
Ambient temperature | -20 ... 70 °C (-4 ... 158 °F) | |
Mechanical specifications | ||
Degree of protection | IP20 | |
Connection | screw terminals | |
Mass | approx. 100 g | |
Dimensions | 12.5 x 114 x 124 mm (0.5 x 4.5 x 4.9 inch) , housing type A2 | |
Mounting | on 35 mm DIN mounting rail acc. to EN 60715:2001 | |
Data for application in connection with hazardous areas | ||
EU-type examination certificate | CESI 10 ATEX 071 | |
Marking | ![]() ![]() ![]() |
|
Input | Ex ia | |
Supply | ||
Maximum safe voltage | 253 V AC (Attention! Um is no rated voltage.) | |
Equipment | terminals 1+, 2- | |
Voltage | 25.2 V | |
Current | 100 mA | |
Power | 630 mW | |
Internal capacitance | 5.7 nF | |
Internal inductance | negligible | |
Equipment | terminals 3+, 4- | |
Voltage | < 30 V | |
Current | < 128 mA | |
Voltage | 7.2 V | |
Current | 100 mA | |
Power | 25 mW | |
Internal capacitance | 5.7 nF | |
Internal inductance | negligible | |
Certificate | CESI 19 ATEX 005 X | |
Marking | ![]() |
|
Directive conformity | ||
Directive 2014/34/EU | EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-7:2015 | |
International approvals | ||
UL approval | E106378 | |
Control drawing | 116-0378 (cULus) | |
IECEx approval | ||
IECEx certificate | IECEx CES 11.0001X | |
IECEx marking | [Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex ec IIC T4 Gc |
|
General information | ||
Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. | |
Accessories | ||
Optional accessories | - power feed module KFD2-EB2(.R4A.B)(.SP) - universal power rail UPR-03(-M)(-S) - profile rail K-DUCT-BU(-UPR-03) |
Manuals | Language | File Type | File Size |
---|---|---|---|
Functional Safety Manual | ENG | 427 KB | |
Manual Isolated Barriers K-system | ENG | 760 KB | |
Manuel pour Barrières Isolées de Système K | FRA | 759 KB | |
Handbuch Trennbarrieren K-System | GER | 745 KB | |
Manual Isolated Barriers K-system | RUS | 4107 KB | |
Instruction manuals | |||
Инструкции | BUL | 152 KB | |
Návod k poużití | CZE | 145 KB | |
Instruktions manual | DAN | 144 KB | |
Instruction manual | ENG | 150 KB | |
Kasutusjuhend | EST | 140 KB | |
Käyttöohje | FIN | 140 KB | |
Manuel d'instructions | FRA | 147 KB | |
Betriebsanleitung | GER | 151 KB | |
Οδηγίες χρήσης | GRE | 155 KB | |
Handleiding | HOL | 146 KB | |
Instruction manual / Betriebsanleitung | HRV | 144 KB | |
Használati útmutató | HUN | 147 KB | |
Manuale di istruzioni | ITA | 146 KB | |
Lietošanas pamācība | LAV | 144 KB | |
Instrukciju vadovas | LIT | 145 KB | |
Instrukcja obsługi | POL | 147 KB | |
Manual de instruções | POR | 147 KB | |
Manual de utilizare | RON | 145 KB | |
Návod na poużitie | SLK | 145 KB | |
Navodila za uporabo | SLV | 143 KB | |
Manual de instrucciones | SPA | 146 KB | |
Manual | SWE | 142 KB |
Statements of compliance | Certificate No. | File Type | File Size |
---|---|---|---|
EU-Declaration of conformity / EU-Konformitätserklärung | DOC-0297D | 442 KB | |
Certificates | |||
Belarus Pattern Approval | Nr. 11709 | 15640 KB | |
Canada UL cUL | E106378 cUL (QUZW7) | LINK | --- |
Canada UL cUL | E106378 cUL (QVAJ7) | LINK | --- |
DNV GL Marine | TAA00001WX | 77 KB | |
EAC EAC TP TC 020/2011 | TC RU C-DE.MH04.B.00397 | 680 KB | |
Europe CESI ATEX Category 3 G | CESI 19 ATEX 005X | 400 KB | |
Europe CESI I (M1) II (1) G II (1) D ATEX Category | CESI 10 ATEX 071 | 629 KB | |
Russia Belarus Kazakhstan EAC EAC TP TC 012/2011 | EAEC RU C-DE.EX01.B.00102/19 | 9815 KB | |
Russia VNIIMS Pattern Approval | DE.C.34.004.A No.56757 | 6680 KB | |
TÜV SÜD Functional Safety Certificate | C-IS-204399-01 | 188 KB | |
USA Canada UL Hazardous Location Certificate of Compliance cULus UL E106378 | CoC 20190524 - E106378 RepRef 20130719 | 254 KB | |
USA UL | E106378 UL (QUZW) | LINK | --- |
USA UL | E106378 UL (QVAJ) | LINK | --- |
Worldwide CESI IECEx Certificate of Conformity | IECEx CES 11.0001X | LINK | --- |
Control drawings | |||
Control Drawing UL / Control Drawing UL | 128 KB |
Accessories | ||||||
---|---|---|---|---|---|---|
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
This isolated barrier is used for intrinsic safety applications.
The device supplies 2-wire transmitters in the hazardous area, and can also be used with current sources.
The device transfers the analog input signal to the non-hazardous area as an isolated current value.
Bi-directional communication is supported for SMART transmitters that use current modulation to transmit data and voltage modulation to receive data.
The output is selected as a current source, current sink, or voltage source via DIP switches.
A fault is signalized by LEDs and a separate collective error message output.
Test sockets for the connection of HART communicators are integrated into the terminals of the device.