工業感測器服務資訊
+886 2 27227708
+886-2-27227782
防爆產品服務資訊
Inductive sensor NRB4-12GS40-E2-IO
- 4 mm flush
- Reduction factor = 1
- Magnetic field resistant
- IO-Link interface for service and process data
- Switch point mode or window mode can be set
- Switching function, stability alarm and pulse extension can be set
请注意：所有以Pepperl + Fuchs GmbH或Pepperl + Fuchs AG名义发行的产品相关文件，例如证书，合格声明等，同样适用于Pepperl + Fuchs SE。
將完整的規格書下載為PDF:
產品規格摘要：的技術資料 NRB4-12GS40-E2-IO
| General specifications | ||
|---|---|---|
| Switching function | Normally open/closed (NO/NC) programmable | |
| Output type | PNP | |
| Rated operating distance | 4 mm (factory setting) | |
| Near operating distance | 3 mm (can be activated by software) | |
| Installation | flush | |
| Output polarity | DC | |
| Assured operating distance | 0 ... 3.24 mm | |
| Reduction factor rAl | 1 | |
| Reduction factor rCu | 1 | |
| Reduction factor r304 | 1 | |
| Reduction factor rSt37 | 1 | |
| Output type | 3-wire | |
| Nominal ratings | ||
| Operating voltage | 10 ... 30 V DC | |
| Switching frequency | 0 ... 2000 Hz (switch point mode) 0 ... 125 Hz (window mode, switch point mode with stability alarm) |
|
| Hysteresis | typ. 3 % | |
| Reverse polarity protection | reverse polarity protected | |
| Short-circuit protection | pulsing | |
| Voltage drop | ≤ 0.5 V | |
| Operating current | 0 ... 200 mA | |
| Off-state current | 0 ... 0.5 mA typ. 60 µA at 25 °C | |
| No-load supply current | ≤ 15 mA | |
| Time delay before availability | max. 150 ms | |
| Constant magnetic field | 200 mT | |
| Alternating magnetic field | 200 mT | |
| Status indicator | LED yellow | |
| Functional safety related parameters | ||
| MTTFd | 362 a | |
| Mission Time (TM) | 20 a | |
| Diagnostic Coverage (DC) | 0 % | |
| Interface | ||
| Interface type | IO-Link ( via C/Q ) | |
| IO-Link revision | 1.1 | |
| Device ID | 0x201101 (2101505) | |
| Transfer rate | COM2 (38.4 kBit/s) | |
| Min. cycle time | 2.3 ms | |
| Process data width | Process data input (control system side): 2 Bit Process data output (control system side): none |
|
| SIO mode support | yes | |
| Compatible master port type | A | |
| Compliance with standards and directives | ||
| Standard conformity | ||
| Standards | EN 60947-5-2:2007 EN 60947-5-2/A1:2012 IEC 60947-5-2:2007 IEC 60947-5-2 AMD 1:2012 |
|
| Approvals and certificates | ||
| Protection class | II | |
| Rated insulation voltage | 60 V | |
| Rated impulse withstand voltage | 800 V | |
| UL approval | cULus Listed, General Purpose Class 2 power source |
|
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) | |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Mechanical specifications | ||
| Connection type | cable PVC , 2 m | |
| Core cross section | 0.34 mm2 | |
| Housing material | Stainless steel 1.4305 / AISI 303 | |
| Sensing face | PBT | |
| Degree of protection | IP67 | |
| Cable | ||
| Cable diameter | 4.3 mm ± 0.1 mm | |
| Bending radius | > 15 x cable diameter | |
| Mass | 66 g | |
| Dimensions | ||
| Length | 40 mm | |
| Diameter | 12 mm | |
| Factory settings | ||
| Default setting | operating mode = switch point mode with stability alarm switching function = Normally open (NO) switching distance = 4 mm |
|
| General information | ||
| Scope of delivery | 2 self locking nuts in scope of delivery | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27274001 |
| ECLASS 12.0 | 27274001 |
| ECLASS 11.0 | 27270101 |
| ECLASS 10.0.1 | 27270101 |
| ECLASS 9.0 | 27270101 |
| ECLASS 8.0 | 27270101 |
| ECLASS 5.1 | 27270101 |
| ETIM 9.0 | EC002714 |
| ETIM 8.0 | EC002714 |
| ETIM 7.0 | EC002714 |
| ETIM 6.0 | EC002714 |
| ETIM 5.0 | EC002714 |
| UNSPSC 12.1 | 39121550 |
Details: NRB4-12GS40-E2-IO
Product Documentation: NRB4-12GS40-E2-IO
| Product information | 語言 | 檔案類型 | 檔案尺寸 |
|---|---|---|---|
| Installation and user instructions for offline parameterization of IO-Link sensors | ENG | 1788 KB | |
| Installation conditions | ENG | 1053 KB | |
| Manuals | |||
| Manual Reduction Factor 1 Sensors with IO-Link | ENG | 1772 KB | |
Design / Simulation: NRB4-12GS40-E2-IO
| CAD | 語言 | 檔案類型 | 檔案尺寸 |
|---|---|---|---|
| CAD 3-D / CAD 3-D | ALL | STP | 49 KB |
| CAD Portal / CAD Portal | ALL | LINK | --- |
Approvals: NRB4-12GS40-E2-IO
| Certificates | 證書號碼 | 語言 | 檔案類型 | 檔案尺寸 |
|---|---|---|---|---|
| Canada USA UL Ordinary Location | UL-US-2019259-3 / UL-CA-2015551-3 | ALL | 288 KB | |
| China Information on CCC | CCC-Exempt Declaration (Pepperl+Fuchs) | ALL | 457 KB | |
| IO-Link Manufacturer Declaration | CERT-5023 | ALL | 162 KB | |
| Declaration of Conformity | ||||
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | DOC-3977C | ALL | 1252 KB | |
| UK Declaration of Conformity (P+F) | TDOC-6240AENG | ENG | 1241 KB | |
Software: NRB4-12GS40-E2-IO
| Device Description Files/Drivers | 發布資訊 | 檔案類型 | 檔案尺寸 |
|---|---|---|---|
| IODD for NRB*-GS-E2-IO / IODD für NRB*-GS-E2-IO | 1.00.000 / 2018-11-01 | ZIP | 344 KB |
| Software Tools | |||
| IO-Link Offline Parameterization Tool / IO-Link Offline-Parametriertool | V1.00.006 / 2022-07-10 | ZIP | 96138 KB |
相關產品: NRB4-12GS40-E2-IO
| Accessories | ||||||
|---|---|---|---|---|---|---|
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
Our amplify article gives interesting insights about the development of the new, modern portfolio of inductive proximity sensors from Pepperl+Fuchs. Get the whole story here!
The knowledge base for inductive sensors contains extensive expertise and supports you in the highly precise and smooth operation of the sensors in your machinery and plants.
符合 SIL 2/PL d 標準的電感式安全感測器進行檢測時沒有盲區，因此資料傳輸可以在感測器與目標之間沒有最小距離的情況下進行。瞭解更多針對嚴苛環境的優化產品組合。
台灣倍加福有限公司
信義路5段150巷2號21樓之4
信義區
11059 台北市 臺灣
臺灣
fa-info@tw.pepperl-fuchs.com
+886 2 27227708
© 2024 版權所有
Pepperl+Fuchs 倍加福是領先全球的電子感測器 和 零組件的開發與製造商. 超過七十年的不斷創新、穩定的品質與持續的業績增長，成就了今日的我們， Pepperl+Fuchs 倍加福在全球擁有 6,300 名員工，並在德國、美國、新加坡、匈牙利、印尼和越南都設有製造工廠，其中多數工廠已通過 ISO 9001 認證