| General specifications |
| Signal type | Analog input |
| Supply |
| Connection | Power Rail or terminals 23+, 24- |
| Rated voltage | 20 ... 35 V DC |
| Ripple | within the supply tolerance |
| Power consumption | max. 3 W |
| Interface |
| Connection | Power Rail or terminals 19+, 20 GND, 21- |
| Type | RS-485 |
| Programming interface | programming socket |
| Field circuit |
| Connection | terminals 1+, 2-, 3+, 4-, 5+, 6- |
| Lead resistance | max. 25 Ω per line |
| Input I | |
| Connection | terminals 1+, 2- |
| Sensor supply | 1 ... 5 V |
| Connection | terminals 3+, 4- (supply); 5+, 6- (signal) |
| Short-circuit current | 50 mA |
| Load | ≥ 116 Ω up to 5V, ≥ 85 Ω up to 4V |
| Input |
| Connection side | field side |
| Connection | Input I: terminals 1+, 2-; Input II: terminals 13+, 14-; Input III: terminals 15+, 14- |
| Programmable Tare | 0 ... 500 % of span |
| Input I | Signal, analog |
| Input signal | -100 ... 100 mV |
| Input resistance | > 1 MΩ for voltage measurement |
| Input II, III | tare adjustment, calibration and zero |
| Open circuit voltage/short-circuit current | 18 V / 5 mA |
| Active/Passive | I > 4 mA/I < 1.5 mA |
| Output |
| Connection side | control side |
| Connection | Output I: terminals 10, 11, 12; Output II: terminals 16, 17, 18; Output III: terminals 7-, 8+, 9- |
| Output I, II | Relay output |
| Contact loading | 253 V AC/2 A/500 VA/cos φ min. 0.7; 40 V DC/2 A resistive load |
| Mechanical life | 2 x 107 switching cycles |
| Output III | Analog output |
| Current range | -20 ... 20 mA |
| Load | max. 550 Ω |
| Analog voltage output | 0 ... ± 10 V; output resistance 500 Ω (bridge between terminal 7 and 9) |
| Analog current output | 0 ... ± 20 mA or 4 ... 20 mA; load 0 ... 550 Ω (terminals 7 and 8) |
| Line fault detection | downscale -21.5 mA (-10.75 V) or 2 mA (1 V), upscale 21.5 mA (10.75 V) |
| Collective error message | Power Rail |
| Transfer characteristics |
| Deviation | |
| Resolution/accuracy | ≤ ± 0.05 % incl. non-linearity and hysteresis |
| Temperature effect | ≤ ± 0.01 %/K |
| Reaction time | 300 ... 850 ms |
| Galvanic isolation |
| Input I/other circuits | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Output I, II against eachother | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Output I, II/other circuits | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Output III/Input II, III | not available |
| Output III/Programming socket | not available |
| Other circuits from each other | functional insulation, rated insulation voltage 50 Veff |
| Indicators/settings |
| Display elements | LEDs , display |
| Control elements | Control panel |
| Configuration | via operating buttons
via PACTware |
| Labeling | space for labeling at the front |
| Directive conformity |
| Electromagnetic compatibility | |
| Directive 2004/108/EC | EN 61326-1:2006 |
| Low voltage | |
| Directive 2006/95/EC | EN 61010-1:2010 |
| Conformity |
| Electromagnetic compatibility | NE 21:2006 |
| Degree of protection | IEC 60529:2001 |
| Ambient conditions |
| Ambient temperature | -20 ... 60 °C (-4 ... 140 °F) |
| Mechanical specifications |
| Degree of protection | IP20 |
| Connection | screw terminals |
| Mass | approx. 250 g |
| Dimensions | 40 x 119 x 115 mm (1.6 x 4.7 x 4.5 inch) (W x H x D) , housing type C2 |
| Height | 119 mm |
| Width | 40 mm |
| Depth | 115 mm |
| Mounting | on 35 mm DIN mounting rail acc. to EN 60715:2001 |
| International approvals |
| UL approval | E223772 |
| General information |
| Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
+886 2 27227708