System components |
Emitter | OBE40M-R200-S-IO-V3-L |
Receiver | OBE40M-R200-EP-IO-V3-L |
General specifications |
Effective detection range | 0 ... 40 m |
Threshold detection range | 50 m |
Light source | laser diode |
Light type | modulated visible red light |
Laser nominal ratings | |
| Note | LASER LIGHT , DO NOT STARE INTO BEAM |
| Laser class | 1 |
| Wave length | 680 nm |
| Beam divergence | > 5 mrad ; d63 < 2 mm in the range of 250 mm ... 750 mm |
| Pulse length | 1.6 µs |
| Repetition rate | max. 17.6 kHz |
| max. pulse energy | 9.6 nJ |
Alignment aid | LED red (in receiver lens) illuminated constantly: beam is interrupted, flashes: reaching switching point, off: sufficient stability control |
Diameter of the light spot | approx. 80 mm at a distance of 40 m |
Opening angle | approx. 0.12 ° |
Ambient light limit | EN 60947-5-2 : 40000 Lux |
Functional safety related parameters |
MTTFd | 440 a |
Mission Time (TM) | 20 a |
Diagnostic Coverage (DC) | 60 % |
Indicators/operating means |
Operation indicator | LED green: constantly on - power on flashing (4Hz) - short circuit flashing with short break (1 Hz) - IO-Link mode |
Function indicator | Yellow LED: Permanently lit - light path clear Permanently off - object detected Flashing (4 Hz) - insufficient operating reserve |
Control elements | Receiver: light/dark switch |
Control elements | Receiver: sensitivity adjustment |
Electrical specifications |
Operating voltage | 10 ... 30 V DC |
Ripple | max. 10 % |
No-load supply current | Emitter: ≤ 13 mA Receiver: ≤ 15 mA at 24 V Operating voltage |
Protection class | III |
Interface |
Interface type | IO-Link ( via C/Q = pin 4 ) |
IO-Link revision | 1.1 |
Device profile | Identification and diagnosis Smart Sensor: Receiver: type 2.4 Emitter: - |
Device ID | Emitter: 0x111402 (1119234) Receiver: 0x111302 (1118978) |
Transfer rate | COM2 (38.4 kBit/s) |
Min. cycle time | 2.3 ms |
Process data width | Emitter: Process data input: 0 bit Process data output: 1 bit Receiver: Process data input: 2 bit Process data output: 2 bit |
SIO mode support | yes |
Compatible master port type | A |
Input |
Test input | emitter deactivation at +UB |
Output |
Switching type | The switching type of the sensor is adjustable. The default setting is: C/Q - Pin4: NPN normally open / dark-on, PNP normally closed / light-on, IO-Link |
Signal output | 1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected, overvoltage protected |
Switching voltage | max. 30 V DC |
Switching current | max. 100 mA , resistive load |
Usage category | DC-12 and DC-13 |
Voltage drop | ≤ 1.5 V DC |
Switching frequency | 1250 Hz |
Response time | 0.4 ms |
Conformity |
Communication interface | IEC 61131-9 |
Product standard | EN 60947-5-2 |
Laser safety | EN 60825-1:2014 |
Approvals and certificates |
UL approval | E87056 , cULus Listed , class 2 power supply , type rating 1 |
CCC approval | CCC approval / marking not required for products rated ≤36 V |
FDA approval | IEC 60825-1:2007 Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 |
Ambient conditions |
Ambient temperature | -40 ... 60 °C (-40 ... 140 °F) |
Storage temperature | -40 ... 70 °C (-40 ... 158 °F) |
Mechanical specifications |
Degree of protection | IP67 / IP69 / IP69K |
Connection | Connector plug, M8 x 1, 3 pin, rotatable by 90° |
Material | |
| Housing | PC (Polycarbonate) |
| Optical face | PMMA |
Mass | Emitter: approx. 35 g receiver: approx. 35 g |
Dimensions | |
| Height | 50.6 mm |
| Width | 15 mm |
| Depth | 41.7 mm |