General specifications |
Design / Mounting | Cabinet installation |
Installation in hazardous area | Zone 1 / Div. 1 |
Fieldbus connection |
Fieldbus type | FOUNDATION Fieldbus |
Physical layer profile | profile type 511 (FISCO), profile type 111 (Entity) |
ITK version | 6.1.1 |
Implementation | resource block 1x RS function block 4x DO, 12x DI, 1x AI, 2x MDI, 1x MDO transducer block 4x TB |
FDE (Fault Disconnect Equipment) | 6.7 mA |
Polarity | not polarity sensitive |
Rated voltage | 9 ... 32 V |
Rated current | max. 23 mA |
Indicators/operating means |
LED PWR | green: on, bus voltage existent |
LED COM ERR | red, continuous lightning: hardware error; red, flashing: no bus activities or bus fault; off: no error |
LED CHANNEL ERROR | red, flashing: lead breakage/short circuit; off: no error |
DIP switch | Address setting , write protection , simulation |
Analog input |
Number of inputs | 1 |
Input type | Frequency input / Counter Input , channel 1 |
| Accuracy | 0.5 % of the measured value |
Switching frequency | min. 0.1 Hz max. 5 kHz |
Pulse duration | min. 80 µs |
Supply voltage | 5 V |
Supply current | 5 mA |
Line fault detection | lead breakage , short circuit (not in counter mode) |
Digital input |
Number of inputs | 12 |
Input type | Sensor input , channels 1, 4, 7, 10 multiplexed , cycle adjustable |
| Supply voltage | 6.6 V |
| Supply current | 5 mA |
| Line fault detection | lead breakage , short circuit |
Input type | Sensor input , channels 2, 3, 5, 6, 8, 9, 11, 12 multiplexed , cycle fixed |
| Supply voltage | 5 V |
| Supply current | 5 mA |
| Time delay before availability | 2 ms |
| Line fault detection | lead breakage , short circuit |
Digital output |
Number of outputs | 4 |
Output type | Low power valve , channels 1, 4, 7, 10 |
Supply voltage | 6.6 V |
Supply current | 1.5 mA |
Line fault detection | lead breakage , short circuit |
Galvanic isolation |
Foundation Fieldbus/Field circuit | safe galvanic isolation acc. to EN 60079-11, voltage peak value 375 V |
Directive conformity |
Electromagnetic compatibility | |
| Directive 2014/30/EU | EN 61326-1:2013 |
Low voltage | |
| Directive 2014/35/EU | EN 61010-1:2010 |
Standard conformity |
Galvanic isolation | EN 60079-11 |
Electromagnetic compatibility | NE 21:2011 |
Degree of protection | IEC/EN 60529 |
Fieldbus standard | IEC 61158-2 |
Shock resistance | EN 60068-2-27 |
Vibration resistance | EN 60068-2-6 |
Ambient conditions |
Ambient temperature | -50 ... 75 °C (-58 ... 167 °F) hazardous area -50 ... 85 °C (-58 ... 185 °F) safe area |
Storage temperature | -40 ... 85 °C (-40 ... 185 °F) |
Relative humidity | ≤ 95 % non-condensing |
Shock resistance | 15 g , 11 ms |
Vibration resistance | 5 g , 10 ... 150 Hz |
Pollution degree | 2 |
Corrosion resistance | acc. to ISA-S71.04-1985, severity level G3 |
Mechanical specifications |
Connection type | spring terminal , pluggable |
Core cross section | |
| Bus | up to 2.5 mm2 |
| Inputs | up to 2.5 mm2 |
Housing material | Polycarbonate |
Degree of protection | IP20 |
Mass | approx. 290 g |
Mounting | DIN rail mounting |
Data for application in connection with hazardous areas |
EU-type examination certificate | BVS 16 ATEX E 075 X |
| Marking | II 2 (1) G Ex ib [ia Ga] IIC T4 Gb , II 3 (1) G Ex ic [ia Ga] IIC T4 Gc , II 3 (1) G Ex ec [ia Ga] IIC T4 Gc , I (M1) [Ex ia Ma] I , II (1) D [Ex ia Da] IIIC |
Field-side | |
| Voltage Uo | 9 V |
| Current Io | 43 mA |
| Power Po | 96 mW |
FOUNDATION Fieldbus | |
| Maximum safe voltage Um | 253 V |
| Voltage Ui | 24 V |
| Current Ii | 380 mA |
| Power Pi | 5.32 W |
Directive conformity | |
| Directive 2014/34/EU | EN 60079-0:2012 , EN 60079-11:2012 , EN 60079-7:2015 |
International approvals |
FM approval | pending |
IECEx approval | IECEx BVS 16.0051X |
| Approved for | Ex ib [ia Ga] IIC T4 Gb , Ex ic [ia Ga] IIC T4 Gc , Ex ec [ia Ga] IIC T4 Gc , [Ex ia Da] IIIC , [Ex ia Ma] I |
Certificates and approvals |
Marine approval | pending |
General information |
Supplementary information | EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com. |