工業感測器服務資訊
+886 2 27227708
+886-2-27227782
防爆產品服務資訊
Ultrasonic sensor UC800-F77S-EP-IO-0,2M-V1-P002
- IO-Link interface for service and process data
- Programmable via DTM with PACTWARE
- Continuous distance value via IO-Link process data
- Selectable sound lobe width
- Synchronization options
- Temperature compensation
- Push-pull output
- Cable with M12 plug
- Customer-specific configuration
请注意：所有以Pepperl + Fuchs GmbH或Pepperl + Fuchs AG名义发行的产品相关文件，例如证书，合格声明等，同样适用于Pepperl + Fuchs SE。
將完整的規格書下載為PDF:
產品規格摘要：的技術資料 UC800-F77S-EP-IO-0,2M-V1-P002
| 產品描述 |
|---|
| Single head system |
| General specifications | ||
|---|---|---|
| Sensing range | 60 ... 800 mm | |
| Adjustment range | 70 ... 800 mm | |
| Dead band | 0 ... 60 mm | |
| Standard target plate | 100 mm x 100 mm | |
| Transducer frequency | approx. 255 kHz | |
| Response delay | minimum : 13 ms factory setting: 49 ms |
|
| Sensor cycle time | ≥ 13 ms (factory setting) ; programmable to 60 s |
|
| Memory | ||
| Non-volatile memory | EEPROM | |
| Write cycles | 300000 | |
| Indicators/operating means | ||
| LED green | solid: power on flashing: standby mode or IO-Link communication |
|
| LED yellow | solid: object in evaluation range flashing: switch point programming, object detected |
|
| LED red | solid: error flashing: switch point programming, object not detected |
|
| Electrical specifications | ||
| Operating voltage | 10 ... 30 V DC , ripple 10 %SS | |
| No-load supply current | ≤ 40 mA | |
| Power consumption | ≤ 400 mW | |
| Time delay before availability | ≤ 300 ms | |
| Interface | ||
| Interface type | IO-Link (via C/Q = Pin 4) | |
| IO-Link revision | 1.1 | |
| Device profile | Smart Sensor | |
| Device ID | 0x300306 (3146502) | |
| Transfer rate | COM2 (38.4 kBit/s) | |
| Min. cycle time | 2.3 ms | |
| Process data width | 16 bit | |
| SIO mode support | yes | |
| Compatible master port type | A | |
| Input/Output | ||
| Input/output type | 1 synchronization connection, bidirectional | |
| 0 Level | 0 ... 1 V | |
| 1 Level | 2.5 V ... UB | |
| Input impedance | > 22 kΩ | |
| Output current | current source < 2.5 mA | |
| Pulse length | ≥ 1 ms with external control, low active | |
| Synchronization frequency | ||
| Common mode operation | ≤ 82 Hz | |
| Multiplex operation | ≤ 82 Hz / n , n = number of sensors , n ≤ 10 |
|
| Output | ||
| Output type | 1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected | |
| Rated operating current | 100 mA , short-circuit/overload protected | |
| Voltage drop | ≤ 2.5 V | |
| Repeat accuracy | ≤ ± 0.1 % of full-scale value | |
| Switching frequency | factory setting: 12 Hz programmable max. 27 Hz | |
| Range hysteresis | 1 % of the adjusted operating range (default settings), programmable , min. 1 mm | |
| Temperature influence | ≤ ± 0.75 % of the end value (with temperature compensation) from 10 minutes after switching on the sensor ; 0.17 %/K (without temperature compensation) | |
| Compliance with standards and directives | ||
| Standard conformity | ||
| Standards | EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 IEC 61131-9:2013 |
|
| Approvals and certificates | ||
| UL approval | cULus Listed, Class 2 Power Source | |
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) When fixing with one M18 nut, the temperature range begins with 0 °C (32 °F). |
|
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Mechanical specifications | ||
| Connection type | fixed cable with plug | |
| Degree of protection | IP67 | |
| Material | ||
| Housing | Polycarbonate | |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam | |
| Connector | ||
| Threading | M12 | |
| Number of pins | 4 | |
| Cable | ||
| Length | 200 mm | |
| Installation position | any position | |
| Mass | 20.5 g | |
| Tightening torque, fastening screws | with M3 nuts max. 0.2 Nm with M18 nuts max. 1 Nm |
|
| Dimensions | ||
| Height | 31 mm | |
| Width | 21 mm | |
| Length | 23 mm | |
| Factory settings | ||
| Output | Switching point 800 mm Output mode: Switching point Output logic: normally open |
|
| Beam width | wide | |
| General information | ||
| Scope of delivery | 2 nuts plastic | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27272803 |
| ECLASS 12.0 | 27272803 |
| ECLASS 11.0 | 27272803 |
| ECLASS 10.0.1 | 27272803 |
| ECLASS 9.0 | 27272803 |
| ECLASS 8.0 | 27272803 |
| ECLASS 5.1 | 27272803 |
| ETIM 9.0 | EC001849 |
| ETIM 8.0 | EC001849 |
| ETIM 7.0 | EC001849 |
| ETIM 6.0 | EC001849 |
| ETIM 5.0 | EC001849 |
| UNSPSC 12.1 | 41111960 |
Details: UC800-F77S-EP-IO-0,2M-V1-P002
Informative Literature: UC800-F77S-EP-IO-0,2M-V1-P002
| Literature | 語言 | 檔案類型 | 檔案尺寸 |
|---|---|---|---|
| Application Report - Ultrasonic sensors measure roll diameter and detect web break | ENG | 172 KB |
Product Documentation: UC800-F77S-EP-IO-0,2M-V1-P002
| Product information | 語言 | 檔案類型 | 檔案尺寸 |
|---|---|---|---|
| Installation and user instructions for offline parameterization of IO-Link sensors | ENG | 1788 KB | |
| Brief Instructions | |||
| Commissioning instruction for UC*-F77*-IU* / Inbetriebnahmeanleitung für UC*-F77*-IU* | ALL | 440 KB | |
| Manuals | |||
| Manual UC***-F77 Series Parameterization of Ultrasonic Sensors with IO-Link Interface | ENG | 4224 KB | |
Approvals: UC800-F77S-EP-IO-0,2M-V1-P002
| Certificates | 證書號碼 | 語言 | 檔案類型 | 檔案尺寸 |
|---|---|---|---|---|
| Canada USA UL Ordinary Location | UL-US-2140030-0 / UL-CA-2133555-0 | ALL | 546 KB | |
| IO-Link Manufacturer Declaration | CERT-4363 | ALL | 254 KB | |
| Declaration of Conformity | ||||
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | DOC-6657 | ALL | 155 KB | |
| UK Declaration of Conformity (P+F) / UK-Konformitäterklärung (P+F) | DOC-6658 | ALL | 143 KB | |
Software: UC800-F77S-EP-IO-0,2M-V1-P002
| Device Description Files/Drivers | 發布資訊 | 檔案類型 | 檔案尺寸 |
|---|---|---|---|
| IODD for UC800-F77S-EP*-P002 / IODD für UC800-F77S-EP*-P002 | V1.00.001 / 2022-07-10 | ZIP | 200 KB |
| Customer specific DTM entry / Kundenspezifischer DTM-Eintrag | 1.0.0 | ZIP | 318 KB |
| DTM (Device Type Manager) Package for UC*-F77* ultrasonic sensors / DTM (Device Type Manager) Package für UC*-F77* Ultraschallsensoren | V1.2.0.2 / 09-08-2022 | ZIP | 12278 KB |
| Software Tools | |||
| IO-Link Offline Parameterization Tool / IO-Link Offline-Parametriertool | V1.00.006 / 2022-07-10 | ZIP | 96138 KB |
相關產品: UC800-F77S-EP-IO-0,2M-V1-P002
| Accessories | ||||||
|---|---|---|---|---|---|---|
|
||||||
|
||||||
|
||||||
|
||||||
台灣倍加福有限公司
信義路5段150巷2號21樓之4
信義區
11059 台北市 臺灣
臺灣
fa-info@tw.pepperl-fuchs.com
+886 2 27227708
© 2024 版權所有
Pepperl+Fuchs 倍加福是領先全球的電子感測器 和 零組件的開發與製造商. 超過七十年的不斷創新、穩定的品質與持續的業績增長，成就了今日的我們， Pepperl+Fuchs 倍加福在全球擁有 6,300 名員工，並在德國、美國、新加坡、匈牙利、印尼和越南都設有製造工廠，其中多數工廠已通過 ISO 9001 認證