工業感測器服務資訊
+886 2 27227708
+886-2-27227782
防爆產品服務資訊
工業感測器
暂不可售
暂不可售

Ultrasonic sensor UC800-F77S-IU-IO-V31-P001

UC800-F77S-IU-IO-V31-P001
  • IO-Link interface for parameterization
  • Programmable via DTM with PACTWARE
  • Selectable sound lobe width
  • Synchronization options
  • Temperature compensation
  • Analog output
  • Customer-specific configuration

请注意：所有以Pepperl + Fuchs GmbH或Pepperl + Fuchs AG名义发行的产品相关文件，例如证书，合格声明等，同样适用于Pepperl + Fuchs SE。

產品規格摘要：的技術資料  UC800-F77S-IU-IO-V31-P001

產品描述
Single head system
General specifications
Sensing range100 ... 800 mm
Adjustment range100 ... 800 mm
Dead band0 ... 100 mm
Standard target plate100 mm x 100 mm
Transducer frequencyapprox. 255 kHz
Response delayminimum : 13 ms
factory setting: 49 ms
Sensor cycle time≥ 13 ms (factory setting) ;
programmable to 60 s
Memory
Non-volatile memoryEEPROM
Write cycles300000
Indicators/operating means
LED greensolid: power on
flashing: standby mode or IO-Link communication
LED yellowsolid: object in evaluation range
flashing: programming of the limits, object detected
LED redsolid: fault
flashing: programming limits, object not detected
Electrical specifications
Operating voltage18 ... 30 V DC , ripple 10 %SS
No-load supply current≤ 50 mA
Power consumption≤ 500 mW
Time delay before availability≤ 300 ms
Interface
Interface typeIO-Link (available after activation via programming button until next reset)
Input/Output
Input/output type1 synchronization connection, bidirectional
0 Level0 ... 1 V
1 Level2.5 V ... UB
Input impedance> 22 kΩ
Output currentcurrent source < 2.5 mA
Pulse length≥ 1 ms with external control, low active
Synchronization frequency
Common mode operation≤ 82 Hz
Multiplex operation≤ 82 Hz / n , n = number of sensors , n ≤ 10
Output
Output type1 analog output 0 (4) ... 20 mA or
1 analog output 0 ... 10 V
Resolutioncurrent output: evaluation range [mm]/3200 but ≥ 0.35 mm
voltage output: evaluation range [mm]/4000 but ≥ 0.35 mm
Deviation of the characteristic curve≤ ± 1 % of full-scale value
Repeat accuracy≤ ± 0.1 % of full-scale value
Load impedancecurrent output: ≤ 500 Ohm
voltage output: ≥ 1000 Ohm
Temperature influence≤ ± 0.75 % of the end value (with temperature compensation) from 10 minutes after switching on the sensor ; 0.17 %/K (without temperature compensation)
Compliance with standards and directives
Standard conformity
StandardsEN IEC 60947-5-2:2020
IEC 60947-5-2:2019
EN 60947-5-7:2003
IEC 60947-5-7:2003
IEC 61131-9:2013
Approvals and certificates
UL approvalcULus Listed, Class 2 Power Source
CCC approvalCCC approval / marking not required for products rated ≤36 V
Ambient conditions
Ambient temperaturecurrent output -25 ... 60 °C (-13 ... 140 °F)
voltage output -25 ... 70 °C (-13 ... 158 °F)
When fixing with one M18 nut, the temperature range for each begins with 0  °C (32 °F).
Storage temperature-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection typeConnector plug M8 x 1 , 4-pin
Degree of protectionIP67
Material
HousingPolycarbonate
Transducerepoxy resin/hollow glass sphere mixture; polyurethane foam
Installation positionany position
Mass13 g
Tightening torque, fastening screwswith M3 nuts max. 0.2 Nm
with M18 nuts max. 1 Nm
Dimensions
Height31 mm
Width21 mm
Length23 mm
Factory settings
Outputnear limit: 100 mm
far limit: 800 mm
Output mode: rising ramp
output type: 4 ... 20 mA
Beam widthwide

Classifications

SystemClasscode
ECLASS 13.027272803
ECLASS 12.027272803
ECLASS 11.027272803
ECLASS 10.0.127272803
ECLASS 9.027272803
ECLASS 8.027272803
ECLASS 5.127272803
ETIM 9.0EC001849
ETIM 8.0EC001849
ETIM 7.0EC001849
ETIM 6.0EC001849
ETIM 5.0EC001849
UNSPSC 12.141111960

Details: UC800-F77S-IU-IO-V31-P001

Datasheet: UC800-F77S-IU-IO-V31-P001

Datasheet檔案類型檔案尺寸
Datasheet UC800-F77S-IU-IO-V31-P001PDF1321 KB
Fiche de données UC800-F77S-IU-IO-V31-P001PDF1330 KB
Datenblatt UC800-F77S-IU-IO-V31-P001PDF1325 KB
Hoja de datos UC800-F77S-IU-IO-V31-P001PDF1349 KB

CAD+CAE: UC800-F77S-IU-IO-V31-P001

CAD檔案類型檔案尺寸
CAD 3-D / CAD 3-DSTP1739 KB
EPLAN
EPLAN macro EDZ / EPLAN Makro EDZEDZ63 KB

相關產品: UC800-F77S-IU-IO-V31-P001

Accessories
Female cordset single-ended M8 straight A-coded, 4-pin, PVC cable greyfa
Cordset M8 socket straight to M12 plug straight A-coded, 4-pin, PVC cable greyfa
Mounting aid for ML7 and ML8 series, Mounting bracketfa
Mounting aid for ML7 and ML8 series, Mounting bracketfa
EtherNet/IP IO-Link master with 8 inputs/outputsfa
PROFINET IO IO-Link master with 8 inputs/outputsfa
Ethernet IO-Link module with 8 inputs/outputsfa
Ethernet IO-Link module with 8 inputs/outputsfa
EtherNet/IP IO-Link master with 8 inputs/outputs, DIN rail, push-in connectorsfa
EtherNet/IP IO-Link master with 8 inputs/outputs, DIN rail, screw terminalfa
PROFINET IO IO-Link master with 8 inputs/outputs, DIN rail, push-in terminalsfa
PROFINET IO IO-Link master with 8 inputs/outputs, DIN rail, screw terminalfa
IO-Link master, supply via USB port or separate power supply, LED indicators, M12 plug for sensor connectionfa
General Notes Relating to Pepperl+Fuchs Product Information
USi-safety Sensor System

USi-safety 超音波感測器系統為安全應用開闢了新的領域，無論是在充滿挑戰性的、多塵的環境中還是在室外…

台灣倍加福有限公司
信義路5段150巷2號21樓之4
信義區
11059 台北市 臺灣
臺灣
fa-info@tw.pepperl-fuchs.com
phone +886 2 27227708

© 2024 版權所有

Pepperl+Fuchs 倍加福是領先全球的電子感測器 和 零組件的開發與製造商. 超過七十年的不斷創新、穩定的品質與持續的業績增長，成就了今日的我們， Pepperl+Fuchs 倍加福在全球擁有 6,300 名員工，並在德國、美國、新加坡、匈牙利、印尼和越南都設有製造工廠，其中多數工廠已通過 ISO 9001 認證