|
|   |
Product |
|
|
The product 'KCD2-E2L' is now added to your watch list.
The product 'KCD2-E2L' is already on your watch list.
|
Single-channel terminal amplifier with line breakage detection, input for NAMUR sensors, DC 24 V supply voltage, standardized interface to prevent signal transmission errors, switching state display, LED yellowfa |
|
|
|
The product 'KCD2-R' is now added to your watch list.
The product 'KCD2-R' is already on your watch list.
|
Relay output with 1 pole, yellow LED indicates switching state, Free-wheeling diode, Compact terminal housing, Clips onto standard 35 mm rail to DIN EN 50 022, Degree of protection IP20fa |
|
|
|
The product 'KFU8-FSSP-1.D' is now added to your watch list.
The product 'KFU8-FSSP-1.D' is already on your watch list.
|
Limit frequency 40 kHz, Voltage or current ouptput, Incrementing output (Spacing factor 1 ... 9999), Multi-range power pack, 2-, 3-, 4-wire and NAMUR sensors as well as rotary encoder connectable, Rated voltage: 200 ... 230 V AC ; 100 … 130 V AC; 50 Hz 20 VDC ... 30 VDCfa |
|
|
|
The product 'KCD2-E1' is now added to your watch list.
The product 'KCD2-E1' is already on your watch list.
|
1-channel terminal amplifier, NAMUR sensor input, DC 24 V supply voltage, Standard interface for prevention of signal transmission errors, Switching status indicator, yellow LEDfa |
|
|
|
The product 'KCD2-E3' is now added to your watch list.
The product 'KCD2-E3' is already on your watch list.
|
1-channel terminal amplifier, NAMUR sensor input, DC 24 V supply voltage, Standard interface for prevention of signal transmission errors, Switching status indicator, yellow LEDfa |
|
|
|
The product 'KCD2-EL' is now added to your watch list.
The product 'KCD2-EL' is already on your watch list.
|
1-channel terminal amplifier, NAMUR sensor input, DC 24 V supply voltage, Standard interface for prevention of signal transmission errors, Switching status indicator, yellow LEDfa |
|
|
|
The product 'K23-SSI/R2/25B-C' is now added to your watch list.
The product 'K23-SSI/R2/25B-C' is already on your watch list.
|
Suitable for the connection of sensors and absolute encoders with SSI interface, Converts both SSI data and serial data into a parallel format, Parallel output 25 bit (Push-pull, short-circuit proof), RS 232 Interface for the serial read out of sensor information, SSI:Master or slave operation fa |
|
|
|
The product 'K23-SSI/Rx/IU-C' is now added to your watch list.
The product 'K23-SSI/Rx/IU-C' is already on your watch list.
|
Multifunction device with operating modes for incremental rotary encoders, SSI absolute rotary encoders, and rotary encoders with start/stop interface, 16 bit analog output, configurable for voltage or current operations, USB interface and RS232/RS485 interface for configuration and readout, Extremely short conversion times, User-definable, non-linear characteristic curve with 24 interpolation pointsfa |
|
|
|
The product 'KFU8-UFC-1.D.FA' is now added to your watch list.
The product 'KFU8-UFC-1.D.FA' is already on your watch list.
|
1-channel signal conditioner, Universal usage at different power supplies, Input for 2- or 3-wire sensors, NAMUR sensors or dry contacts, Input frequency 1 mHz ... 10 kHz, Current output 0/4 mA ... 20 mA, Relay contact and transistor output, Start-up override, Line fault detection (LFD), Up to SIL 2 acc. to IEC 61508/IEC 61511pa |
|
|
|
The product 'KFU8-UFT-2.D.FA' is now added to your watch list.
The product 'KFU8-UFT-2.D.FA' is already on your watch list.
|
2-channel signal conditioner, Universal usage at different power supplies, Dry contact or NAMUR inputs, Input frequency 1 mHz ... 1 kHz, Current output 0/4 mA ... 20 mA, Relay contact and transistor output, Start-up override, Configurable by PACTware or keypad, Line fault detection (LFD), Rated voltage: 20 ... 90 V DC / 48 ... 253 V AC 50 ... 60 Hzpa |
|
|
|   |