Sensor Interface FD0-BI-EX12.PA
- For 12 intrinsically safe binary inputs
- Installation in Zone 1 and Zone 2
- Sensors in Zone 0
- Connection to fieldbus acc. to FISCO or Entity
- For PROFIBUS PA
- Galvanic separation between bus and sensors
- EMC acc. to NAMUR NE 21
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
데이타 시트 발췌: 기술 사양 FD0-BI-EX12.PA
| General specifications | ||
|---|---|---|
| Design / Mounting | Outside installation | |
| Fieldbus connection | ||
| PROFIBUS PA | ||
| Connection | Connection +, - | |
| Rated voltage | 9 ... 32 V | |
| Rated current | max. 23 mA | |
| Baud rate | 31.25 kBit/s | |
| Protocol | PROFIBUS DP V1 | |
| Terminal "S" | only for the connection of the cable screen (BUS) and/or the potential compensation | |
| Terminal "PA" | only for the connection of the cable screen (sensor interface) and/or grounding | |
| Grounding plate | only for the connection of the potential compensation | |
| Field circuit | ||
| Inputs | ||
| Connection | 4, for binary sensors: terminals 1+, 2-, 5+, 6-, 9+, 10-, 13+, 14- 8, for binary sensors: terminals 3, 4, 7, 8, 11, 12, 15, 16 |
|
| Sensor supply voltage | 4, for binary sensors: 5.5 V 8, for binary sensors: 5 V |
|
| Sensor supply current | 4, for binary sensors: 4.5 mA 8, for binary sensors: ≤ 5 mA |
|
| Time delay before availability | for 4 binary sensors, 1 s for 8 binary sensors, < 3 ms |
|
| Max. cycle time | for binary 4 sensors, 4 x 1 s = 4 s for 8 binary sensors, 8 x 12.5 ms = 100 ms |
|
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | EN 61326-1:2013 | |
| Standard conformity | ||
| Galvanic isolation | EN 60079-11 | |
| Electromagnetic compatibility | NE 21:2006 | |
| Degree of protection | IEC/EN 60529 | |
| Fieldbus standard | EN 50170/2 | |
| Ambient conditions | ||
| Ambient temperature | -20 ... 70 °C (-4 ... 158 °F) | |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Corrosion resistance | acc. to ISA-S71.04-1985, severity level G3 | |
| Mechanical specifications | ||
| Core cross section | Bus cable:∅ 5 mm ... 10 mm cable sensors: ∅ 4 mm ... 8 mm |
|
| Housing | 187 mm x 129 mm x 46 mm | |
| Degree of protection | IP65 | |
| Installation position | Cable glands downwards | |
| Mass | approx. 290 g | |
| Mounting | wall mounting | |
| Data for application in connection with hazardous areas | ||
| EU-type examination certificate | PTB 98 ATEX 2210 | |
| Marking |  II 2G (1) Ex ia [ia Ga] IIC T4 Gb , II (1D) [Ex ia Da] IIIC , II 3G Ex ic IIC T4 Gc , II (3D) [Ex ic Dc] IIIC |
|
| PROFIBUS PA | ||
| Voltage | 24 V | |
| Current | 380 mA | |
| Power | 5.32 W | |
| Rated voltage | 9 ... 32 V | |
| Rated current | 23 mA | |
| FDE (Fault Disconnect Equipment) | 6.7 mA | |
| Terminal "S" | only for the connection of the cable screen (BUS) and/or the potential compensation | |
| Terminal "PA" | only for the connection of the cable screen (sensor interface) and/or grounding | |
| Grounding plate | only for the connection of the potential compensation | |
| Field-side | ||
| Voltage | 9 V | |
| Current | 44 mA | |
| Power | 99 mW | |
| Directive conformity | ||
| Directive 2014/34/EU | EN 60079-0:2012 , EN 60079-11:2012 | |
| International approvals | ||
| IECEx approval | IECEx TUN 04.0002 | |
| Approved for | Ex ia [ia Ga] IIC T4 Gb , [Ex ia Da] IIIC , Ex ic IIC T4 Gc , [Ex ic Dc] IIIC |
|
| General information | ||
| Supplementary information | EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com. | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27242610 |
| ECLASS 12.0 | 27242610 |
| ECLASS 11.0 | 27242610 |
| ECLASS 10.0.1 | 27242610 |
| ECLASS 9.0 | 27242610 |
| ECLASS 8.0 | 27242610 |
| ECLASS 5.1 | 27242610 |
| ETIM 9.0 | EC001601 |
| ETIM 8.0 | EC001601 |
| ETIM 7.0 | EC001601 |
| ETIM 6.0 | EC001601 |
| ETIM 5.0 | EC001604 |
| UNSPSC 12.1 | 39121008 |
Details: FD0-BI-EX12.PA
Datasheet: FD0-BI-EX12.PA
| Datasheet | 파일 타입 | 파일 크기 |
|---|---|---|
| Datasheet FD0-BI-EX12.PA | 816 KB | |
| Datenblatt FD0-BI-EX12.PA | 1695 KB |
Documents: FD0-BI-EX12.PA
Approvals+Certificates: FD0-BI-EX12.PA
| Certificates | 파일 타입 | 파일 크기 |
|---|---|---|
| Europe PTB II 2 G (1) II (1D) II (3D) II 3 G ATEX | 1378 KB | |
| TUV Nord IECEx Certificate of Conformity | LINK | --- |
| Declaration of Conformity | ||
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | 88 KB |
Software: FD0-BI-EX12.PA
| Device Driver | 파일 타입 | 파일 크기 |
|---|---|---|
| GSD / GSD | ZIP | 4 KB |
Ethernet-APL enables continuous communication across all hierarchy levels. Learn more about the pioneering technology …
RSS Info Service for PANOS Updates
Stay informed when a new software update of PANOS, the operating system for Ethernet-APL switches, is released: With our RSS Feed you will get an email notfication in your inbox immediately after an update has been released.
From decisions to planning, installation, and commissioning up to operation and maintenance: Discover how to make the most out of your fieldbus infrastructure …
페펄앤드푹스코리아(주)
서울특별시 서초구 서초대로88
6층 (유니온빌딩)
06673 대한민국
대한민국
info@kr.pepperl-fuchs.com
+82 2 34819494
Pepperl+Fuchs는 세계 자동화 시장에서 전자기 센서 및 컴포넌트 제조 및 개발의 선두주자입니다. 지속적인 혁신, 오래토록 변치 않는 품질 및 꾸준한 성장이 지난 70년 동안 계속적인 성장을 보장하였습니다. Pepperl+Fuchs의 전세계에 6,300명의 임직원을 보유하고 있으며, 독일, USA, 싱가포르, 헝가리, 인도네시아 및 베트남에 제조 시설을 가지고 있으며, 대부분 ISO9001을 획득하였습니다.