Strain Gauge Converter KFD2-WAC2-1.D

1-channel signal conditioner
24 V DC supply (Power Rail)
Strain gauge input (full or half bridge)
Output 0 mA ... ± 20 mA or 0 V ... ± 10 V
2 relay contact outputs
Programmable high/low alarm
Configurable by PACTware or keypad
RS-485 interface
Line fault detection (LFD)

Technical Data
Informative Literature
Product Documentation
Design / Simulation
Approvals
Software
Tilhørende produkter

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Hent hele databladet som PDF:

Uddrag af datablad: Tekniske data for KFD2-WAC2-1.D

General specifications
Signal type		Analog input
Supply
Connection		Power Rail or terminals 23+, 24-
Rated voltage		20 ... 35 V DC
Ripple		within the supply tolerance
Power consumption		max. 3 W
Interface
Connection		Power Rail or terminals 19+, 20 GND, 21-
Type		RS-485
Programming interface		programming socket
Field circuit
Connection		terminals 1+, 2-, 3+, 4-, 5+, 6-
Lead resistance		max. 25 Ω per line
Input I
	Connection	terminals 1+, 2-
Sensor supply		1 ... 5 V
	Connection	terminals 3+, 4- (supply); 5+, 6- (signal)
	Short-circuit current	50 mA
	Load	≥ 116 Ω up to 5V, ≥ 85 Ω up to 4V
Input
Connection side		field side
Connection		Input I: terminals 1+, 2-; Input II: terminals 13+, 14-; Input III: terminals 15+, 14-
Programmable Tare		0 ... 500 % of span
Input I		Signal, analog
	Input signal	-100 ... 100 mV
	Input resistance	> 1 MΩ for voltage measurement
Input II, III		tare adjustment, calibration and zero
	Open circuit voltage/short-circuit current	18 V / 5 mA
	Active/Passive	I > 4 mA/I < 1.5 mA
Output
Connection side		control side
Connection		Output I: terminals 10, 11, 12; Output II: terminals 16, 17, 18; Output III: terminals 7-, 8+, 9-
Output I, II		Relay output
	Contact loading	253 V AC/2 A/500 VA/cos φ min. 0.7; 40 V DC/2 A resistive load
	Mechanical life	2 x 10⁷ switching cycles
Output III		Analog output
	Current range	-20 ... 20 mA
	Load	max. 550 Ω
	Analog voltage output	0 ... ± 10 V; output resistance 500 Ω (bridge between terminal 7 and 9)
	Analog current output	0 ... ± 20 mA or 4 ... 20 mA; load 0 ... 550 Ω (terminals 7 and 8)
Line fault detection		downscale -21.5 mA (-10.75 V) or 2 mA (1 V), upscale 21.5 mA (10.75 V)
Collective error message		Power Rail
Transfer characteristics
Deviation
	Resolution/accuracy	≤ ± 0.05 % incl. non-linearity and hysteresis
	Temperature effect	≤ ± 0.01 %/K
Reaction time		300 ... 850 ms
Galvanic isolation
Input I/other circuits		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V_eff
Output I, II against eachother		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V_eff
Output I, II/other circuits		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V_eff
Output III/Input II, III		not available
Output III/Programming socket		not available
Other circuits from each other		functional insulation, rated insulation voltage 50 V_eff
Indicators/settings
Display elements		LEDs , display
Control elements		Control panel
Configuration		via operating buttons via PACTware
Labeling		space for labeling at the front
Directive conformity
Electromagnetic compatibility
	Directive 2004/108/EC	EN 61326-1:2006
Low voltage
	Directive 2006/95/EC	EN 61010-1:2010
Conformity
Electromagnetic compatibility		NE 21:2006
Degree of protection		IEC 60529:2001
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Mechanical specifications
Degree of protection		IP20
Connection		screw terminals
Mass		approx. 250 g
Dimensions		40 x 119 x 115 mm (1.6 x 4.7 x 4.5 inch) (W x H x D) , housing type C2
	Height	119 mm
	Width	40 mm
	Depth	115 mm
Mounting		on 35 mm DIN mounting rail acc. to EN 60715:2001
International approvals
UL approval		E223772
General information
Supplementary information		Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210120
ECLASS 12.0	27210190
ECLASS 11.0	27210190
ECLASS 10.0.1	27210190
ECLASS 9.0	27210190
ECLASS 8.0	27210190
ECLASS 5.1	27210107
ETIM 9.0	EC002476
ETIM 8.0	EC002476
ETIM 7.0	EC002476
ETIM 6.0	EC002476
ETIM 5.0	EC001485
UNSPSC 12.1	32101514

Details: KFD2-WAC2-1.D

Informative Literature: KFD2-WAC2-1.D

Literature	Sprog	Fil type	Fil størrelse
Application Report - Generating Electricity in Coal-Fired Power Plants	ENG	PDF	412 KB
Application Report - Screening Systems in Sewage Treatment Plants	ENG	PDF	577 KB

Product Documentation: KFD2-WAC2-1.D

Brief Instructions	Sprog	Fil type	Fil størrelse
Operator card KF-WAC2-1.D / Bedienkarte KF-WAC2-1.D	ALL	PDF	928 KB
Safety and Security Documentation
Instruktions manual	DAN	PDF	47 KB
Manuals
Manual KF**-WAC2-(Ex)1.D	ENG	PDF	1799 KB
System Manual	ENG	PDF	3694 KB
Installation and configuration guide Device Type Manager (DTM)	ENG	PDF	8665 KB

Design / Simulation: KFD2-WAC2-1.D

CAD	Sprog	Fil type	Fil størrelse
CAD 3-D / CAD 3-D	ALL	STP	2722 KB
CAD Portal / CAD Portal	ALL	LINK	---
CAE
CAE EPLAN Data Portal / CAE EPLAN Data Portal	ALL	LINK	---
EPLAN macro EDZ / EPLAN Makro EDZ	ALL	EDZ	86 KB

Approvals: KFD2-WAC2-1.D

Certificates	Certifikat nr.	Sprog	Fil type	Fil størrelse
USA Canada UL cULus Hazardous Location UL E223772 UL	CoC 20200622 - E223772 RepRef 20071210	ALL	PDF	82 KB

Software: KFD2-WAC2-1.D

Device Description Files/Drivers	Udgivelses info	Fil type	Fil størrelse
DTM Collection Interface Technology 2 / DTM Collection Interface Technology 2	1.4.110.77	ZIP	---
Software Tools
PACTware 4.1 SP6 / PACTware 4.1 SP6	4.1.0.53	ZIP	43327 KB
PACTware 5.0 / PACTware 5.0	5.0.5.31	ZIP	44203 KB
PACTware 6.X / PACTware 6.X	6.1	ZIP	335938 KB

Tilhørende produkter: KFD2-WAC2-1.D

Matching System Components

	DTM Interface Technology DTM collection
	Device DTM, For K-, E- and H-System, Frame application, like e. g. PACTware, must be installed separatelypa

	PACTware 5.0 FDT Framework
	Universal DTM host platform, For all DTMs of Pepperl+Fuchs, Approved FDT/DTM technology, Free of charge, Download from Pepperl+Fuchs websitepa

	K-ADP-USB Adapter with USB Interface
	Isolated USB interface cable, Used with K-, E- and H-System devices, Used with PACTwarepa

	K-DUCT-GY Profile Rail
	Cable trunking is integrated in the mounting profile, Safe spacious separation of field and control signals, No additional cable guides necessary, Standard length 1.8 m (5.8 ft), simple to customize to application space, With mounting aidspa

	PACTware 6.x FDT Framework
	Universal DTM host platform, For all DTMs of Pepperl+Fuchs, Approved FDT/DTM technology, Free of charge, Download from Pepperl+Fuchs websitepa

Accessories

	KF-ST-5GN Terminal Block
	3-pin screw terminal, For KF modules of K-System, Packaging unit: 5 pieces greenpa

	KF-CP Coding Pins
	Coding of K-System terminal blocks, Coding of LB/FB-System front sockets, Packaging unit: 20 x 6 coding pinspa

Generelle bemærkninger vedr. produktoplysninger fra Pepperl+Fuchs

Hurtige links

Selector for Safety Products

Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.

Pepperl+Fuchs A/S
Kirkebjerg Allé 90
DK-2605 Brøndby
Denmark
info@dk.pepperl-fuchs.com
phone +45 7010 4210

Pepperl+Fuchs er markedsledende indenfor udvikling og fabrikation af elektroniske sensorer og komponenter til det globale automatiseringsmarked. Kontinuerlig innovation, kombineret med høj kvalitet og stabil vækst har sikret uafbrudt succes gennem mere end 70 år. Pepperl+Fuchs har 6.300 ansatte på verdensplan og har produktionsfaciliteter i Tyskland, USA, Singapore, Ungarn, Indonesien og Vietnam; de fleste ISO 9001 certificerede.