WirelessHART Adapter WHA-ADP-F8B2-*-P*-Z1(-Ex1)
- 1-channel
- Installation in Zone 1
- WirelessHART Adapter
- Battery operated
- Also supplies field device
- Input 2-wire HART transmitters and 2-wire HART current sources
- Output WirelessHART wireless interface
- Direct mounting on HART or 4 mA ... 20 mA field device
- Rotatable antenna
请注意：所有以Pepperl + Fuchs GmbH或Pepperl + Fuchs AG名义发行的产品相关文件，例如证书，合格声明等，同样适用于Pepperl + Fuchs SE。
下载PDF版完整参数表:
技术参数节选 WHA-ADP-F8B2-*-P*-Z1(-Ex1)
| Supply | ||
|---|---|---|
| Rated voltage | 7.2 V DC , battery operated | |
| Electrical specifications | ||
| Output current | 4 ... 20 mA | |
| Supply | loop power for field devices voltage 8 ... 23 V DC, adjustable in steps of 0.1 V |
|
| Input | ||
| Connection | terminals 1, 2, 3, 4, 5, 6 multiple wirings available , depending on operating mode |
|
| Current | 4 ... 20 mA | |
| HART communication | ||
| Protocol | HART 7.1, backward compatible | |
| Number of devices | - one passive 4 ... 20 mA/HART field device - up to 4 HART field devices in multidrop mode |
|
| Transfer rate | 1200 Bit/s | |
| Parameters | primary/secondary master, preambles, retries and short address scan ranges | |
| Output | ||
| Interface | omnidirectional dipole antenna, adjustable in vertical plane | |
| Output variables | PV: loop current SV, TV, QV:configurable according to user requirement - adapter: temperature, battery voltage, energy consumed and estimated battery life-time - 4 ... 20 mA device: scaled or linearized process value - HART device: up to four process variables |
|
| Communication | WirelessHART specifications - physical layer: IEEE 802.15.4.2006 - frequency band: 2.4 GHz (ISM band, licence free) - transmission rate: 250 kBit/s - maximum transmit power: +10 dBm (EIRP) - transmission range: outdoor 250 m, indoor 50 m (under reference conditions) - communication standard: WirelessHART |
|
| Transfer characteristics | ||
| Accuracy | current input: 0.125 % of measuring range | |
| Influence of ambient temperature | current input: 5 µA/K | |
| Indicators/settings | ||
| Display elements | green LED: battry status yellow LED: communication status red LED: device status |
|
| Control elements | 1 push botton for: - device status - enter/leave configuration mode - join trigger - factory reset |
|
| Configuration | wired interface: - HART 7.1, FSK compatible - transmission rate: 1200 Bit/s - used for device commissioning with an handheld terminal or a configuration tool (DTM) |
|
| Parameter assignment | - wireless transmit power: configurable to 0 dBm or 10 dBm (EIRP) - device variables mapping - publishing of up to ten burst messages in a wireless network, period and trigger mode selectable - notification of up to five events from adapter and/or connected device(s) in a wireless network - scaling and linearization of 4 ... 20 mA signal of connected analog device - tuning of supply parameters for the connected device - locking/unlocking of device parameterization |
|
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2004/108/EC | EN 61326-1:2006 | |
| Radio and telecommunication terminal equipment | The usage of 2.4 GHz equipment is bound to local restrictions. Ensure that restrictions allow usage of this product before commisioning. | |
| Directive 99/5/EC | ETSI EN 300328: V1.7.1 (2006-10), ETSI EN 301489-17: V1.2.1 (2002-08), EN 60950:2001 | |
| FCC CFR47 Part 15 B and C | ANSI C63.4-2003 | |
| Conformity | ||
| Degree of protection | IEC 60529 | |
| Shock resistance | EN 60068-2-27 | |
| Vibration resistance | EN 60068-2-64 | |
| Ambient conditions | ||
| Ambient temperature | -40 ... 60 °C (-40 ... 140 °F) | |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Relative humidity | max. 90 % , noncondensing | |
| Vibration resistance | 20 ... 2000 Hz, 0,01 g2/Hz | |
| Impact resistance | 15 g, 11 ms | |
| Corrosion resistance | acc. to ISA-S71.04-1985, severity level G3 test setup and execution acc. to EN 60068-2-60 |
|
| Mechanical specifications | ||
| Degree of protection | IP66 | |
| Cable entry | M20 x 1.5 ; enclosed cable gland | |
| Material | plastic | |
| Mass | approx. 750 g | |
| Dimensions | 91 x 88.5 x 100.6 mm (3.6 x 3.5 x 4 inch) (without cable glands and antenna) | |
| Height | 192 mm | |
| Width | 110.4 mm | |
| Depth | 100.6 mm | |
| Mounting | mounting on field device , panel or pole mounting versions see type code |
|
| Data for application in connection with hazardous areas | ||
| EU-type examination certificate | BVS 11 ATEX E 081 , for additional certificates see www.pepperl-fuchs.com | |
| Marking |  II 2 G Ex ia IIC T4 Gb |
|
| Directive conformity | ||
| Directive 94/9/EC | EN 60079-0:2009 , EN 60079-11:2007 , EN 60079-31:2009 | |
| International approvals | ||
| IECEx approval | BVS 11.0061 | |
| General information | ||
| Supplementary information | EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com. | |
| Accessories | ||
| Designation | battery W-BAT-B2-Li mandatory for use in connection with hazardous areas (order separately) mounting set W-ACC-MKF8 |
|
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27210192 |
| ECLASS 12.0 | 27210192 |
| ECLASS 11.0 | 27210192 |
| ECLASS 10.0.1 | 27210190 |
| ECLASS 9.0 | 27210190 |
| ECLASS 8.0 | 27210190 |
| ECLASS 5.1 | 27242692 |
| ETIM 9.0 | EC001604 |
| ETIM 8.0 | EC001604 |
| ETIM 7.0 | EC001604 |
| ETIM 6.0 | EC001604 |
| ETIM 5.0 | EC001604 |
| UNSPSC 12.1 | 39121008 |
| Product category / 产品类的 |
Details: WHA-ADP-F8B2-*-P*-Z1(-Ex1)
Product Documentation: WHA-ADP-F8B2-*-P*-Z1(-Ex1)
| Brief Instructions | 语言 | 文件类型 | 文件大小 |
|---|---|---|---|
| Brief Instructions - WirelessHART Adapter Firmware Update Instructions | ENG | 2449 KB | |
| Brief Instructions - WirelessHART Network | ENG | 2045 KB | |
| Safety and Security Documentation | |||
| Instruction manual | ENG | 65 KB | |
| Manuals | |||
| Manual WirelessHART Adapter WHA-ADP-F8B2-*-**-Z1(-EX1) | ENG | 3318 KB | |
| Software Information | |||
| Software Release Notes WHA-ADP | ENG | 42 KB | |
Approvals: WHA-ADP-F8B2-*-P*-Z1(-Ex1)
| Certificates | 证书号码 | 语言 | 文件类型 | 文件大小 |
|---|---|---|---|---|
| Canada USA CSA | CoC 2535301 | ALL | 114 KB | |
| DEKRA EXAM IECEx Certificate of Conformity | IECEx BVS 11.0061 | ALL | LINK | --- |
| India Radio Approval | ETA 2025/2012/WRLO | ALL | 660 KB | |
| Japan CETECOM ICT Radio / Connection | 202-LSA063 / D 12-0050-202 | ALL | 175 KB | |
| Korea Radio Approval | KCC-RRM-PFG-WHA-ADP | ALL | 706 KB | |
| Declaration of Conformity | ||||
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | DOC-0459C | ALL | 240 KB | |
Software: WHA-ADP-F8B2-*-P*-Z1(-Ex1)
| Device Description Files/Drivers | Release Info | 文件类型 | 文件大小 |
|---|---|---|---|
| DTM Collection WirelessHART V1.0.2.4 / DTM Collection WirelessHART V1.0.2.4 | ZIP | 22259 KB |
倍加福（北京）过程自动化控制设备有限公司
北京市经济技术开发区
科创十四街99号7号楼3101室
101111 Beijing
中国
pa-info@cn.pepperl-fuchs.com
+86 10 5901 7000
上海倍加福工业自动化贸易有限公司
上海市静安区市北工业园区江场三路
219号4楼
200436 上海
中国
fa-info@cn.pepperl-fuchs.com
+86 21 6630 3939
沪ICP备20009978号 | © 2024 版权所有。
德国倍加福公司（P+F）是全球自动化行业中久负盛名的专业传感器公司。倍加福作为全球自动化领域的电子传感与零部件的生产主导者，凭借不断的创新，恒久的质量保证，稳健的发展，保证了迄今六十余年的辉煌成就。倍加福在全球范围内拥有6300名员工，位于德国，美国，新加坡，匈牙利，印度尼西亚和越南的生产基地几乎全部通过了ISO9001的质量认证。