No disponible para compra

Universal Temperature Converter ED2-UT-Ex2

2-channel isolated barrier
24 V DC supply
Thermocouple or RTD input
Current output 0/4 mA ... 20 mA
Configurable by PACTware
Line fault (LFD) and sensor burnout detection
Internal cold junction compensation

Technical Data
Product Documentation

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Descargue la hoja de datos completa en PDF:

Extracto de la hoja de datos: Información técnica del ED2-UT-Ex2

General specifications
Signal type		Analog input
Supply
Connection		d14+, z14-
Rated voltage		20 ... 30 V DC
Ripple		within the supply tolerance
Power consumption		max. 3 W
Input
Connection		channel 1: d2, d4, d6, d8 channel 2: z2, z4, z6, z8
RTD		type Pt100 (EN 60751: 1995) type Ni100 (DIN 43760)
	Measuring current	approx. 400 µA with RTD
	Types of measuring	2-, 3-, 4-wire connection
	Lead resistance	max. 50 Ω per line
	Measurement loop monitoring	line fault
Thermocouples		type B, E, J, K, N, R, S, T (IEC 584-1: 1995), type L (IEC 584-1: 1989)
	Cold junction compensation	external and internal , see connection diagram
	Measurement loop monitoring	sensor breakage
Resistor
	Measurement range	0 ... 400 Ω
Voltage
	Measurement range	-240 ... 240 mV
Output
Connection		channel 1: d30+, z30- channel 2: d32+, z32-
Current range		0/4 ... 20 mA
Load		max. 500 Ω
Output		Analog current output
Fault signal		in case of input signal overrange 20.5 mA
Line fault detection		downscale 0 or 2 mA, upscale 21.5 mA (acc. NAMUR NE43)
Transfer characteristics
Deviation
	After calibration	Pt100: ± (0.01 % of measurement value in K + 0.05 % of span + 0.1 K (4-wire connection)) thermocouple: ± (0.05 % of measurement value in °C + 0.05 % of span + 1 K (1.2 K for types R and S)) this includes ± 0.8 K fault of the cold junction compensation (CJC): mV: ± (50 µV + 0.1 % of span) potentiometer: ± (0.05 % of full scale + 0.1 % of span, (excludes faults due to lead resistance))
	Influence of ambient temperature	influence of cold junction compensation (CJC) included: Pt100: ± (0.0015 % of measurement value in K + 0.006 % of span)/K ΔT_amb^) thermocouple: ± (0.02 K + 0.004 % of measurement value in °C + 0.006 % of span)/K ΔT_amb^) ^*) ΔT_amb = ambient temperature change referenced to 23 °C (296 K)
	Influence of supply voltage	< 0.01 % of span
	Influence of load	≤ 0.001 % of output value per 100 Ω
Galvanic isolation
Output/power supply		functional insulation, rated insulation voltage 50 V_eff
Output/Output		functional insulation, rated insulation voltage 50 V_eff
Directive conformity
Electromagnetic compatibility
	Directive 2004/108/EC	The device has been used for the same applications for several years. It therefore features an appropriate electromagnetic field immunity. The device must not be used in new plants.
Conformity
Insulation coordination		EN 50178
Electromagnetic compatibility		NE 21:2006
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Mechanical specifications
Degree of protection		IP20
Connection		48-pin plug connector acc. to DIN 41612 , series 2 , type F , z, b and d provided
Mass		approx. 200 g
Dimensions		20 x 128 x 193 mm (0.8 x 5 x 7.6 inch)
	Height	128 mm
	Width	20 mm
	Length	193 mm
Construction type		Eurocard 100 x 160 mm (3.9 x 6.3 inch) acc. to DIN 41494, front panel 4TE
Mounting		in 19" rack
Coding		a15/a27
Data for application in connection with hazardous areas
EU-type examination certificate		BAS 00 ATEX 7044 X , for additional certificates see www.pepperl-fuchs.com
	Marking	II (1)GD [Ex ia] IIC, [Ex iaD] (-20 °C ≤ T_amb ≤ 60 °C) [circuit(s) in zone 0/1/2]
	Input	Ex ia IIC
	Voltage	11 V
	Current	33 mA
	Power	90 mW (linear characteristic)
Supply
	Maximum safe voltage	250 V (Attention! The rated voltage is lower.)
Output
	Maximum safe voltage	250 V (Attention! The rated voltage is lower.)
Galvanic isolation
	Input/Other circuits	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 94/9/EC	EN 60079-0:2006, EN 60079-11:2007, EN 61241-0:2006, EN 61241-11:2005
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Accessories
Designation		optional accessories: - cold junction module E-CJC - programming adapter K-ADP-USB - configuration software PACTware^TM

Classifications

System	Classcode
ECLASS 13.0	27210129
ECLASS 12.0	27210129
ECLASS 11.0	27210129
ECLASS 10.0.1	27210129
ECLASS 9.0	27210129
ECLASS 8.0	27210190
ECLASS 5.1	27210107
ETIM 9.0	EC002919
ETIM 8.0	EC002919
ETIM 7.0	EC002919
ETIM 6.0	EC002919
ETIM 5.0	EC001485
UNSPSC 12.1	32101514

Details: ED2-UT-Ex2

Product Documentation: ED2-UT-Ex2

Manuals	Idioma	Tipo de archivo	Tamaño
Brief Instructions - E-system	ENG	PDF	320 KB
Installation and configuration guide Device Type Manager (DTM)	ENG	PDF	8665 KB

Notas generales sobre la información de los productos de Pepperl+Fuchs

Enlaces directos

Pepperl+Fuchs SE
Lilienthalstraße 200
68307 Mannheim
Germany
info@de.pepperl-fuchs.com
phone +49 621 776-0

Pepperl + Fuchs es líder en el desarrollo y la fabricación de sensores electrónicos y componentes para el mercado de la automatización global. Su incesante innovación, calidad duradera y crecimiento constante garantizan el éxito continuado, desde hace más de 70 años. Pepperl + Fuchs emplea a 6.300 personas en todo el mundo y cuenta con fábricas en Alemania, EE.UU., Singapur, Hungría, Indonesia y Vietnam, la mayoría de ellas con certificado ISO 9001.