Línea de servicio de Sensores Industriales
Atención al cliente para protección contra explosiones
Protección contra Explosiones
No disponible para compra
No disponible para compra

HART Transmitter Power Supply, Input Isolator FB3205B

FB3205B
  • 4-channel
  • Inputs Ex ia
  • Installation in suitable enclosures in Zone 1
  • Module can be exchanged under voltage (hot swap)
  • Power supply for 2- or 3-wire transmitters with 4 mA ... 20 mA
  • Supply circuit 15 V (20 mA)
  • Input from active signals of 4-wire transmitters
  • HART communication via field bus or service bus
  • Simulation mode for service operations (forcing)
  • Line fault detection (LFD)
  • Permanently self-monitoring

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Extracto de la hoja de datos: Información técnica del  FB3205B

Supply
Connectionbackplane bus
Rated voltage12 V DC , only in connection with the power supplies FB92**
Power consumption3 W
Internal bus
Connectionbackplane bus
Interfacemanufacturer-specific bus to standard com unit
Input
Number of channels4
Suitable field devicestransmitters for pressure, differential pressure, level, flow, temperature, etc.
Connection2-wire transmitter (HART):
supply circuit: channel I 1+, 2-, channel II 5+, 6-, channel III 9+, 10-, channel IV 13+, 14-
3-wire transmitter:
supply circuit: channel I 1+, 4-, channel II 5+, 8-, channel III 9+, 12-, channel IV 13+, 16-
measuring circuit: channel I 3+, 4-, channel II 7+, 8-, channel III 11+, 12-, channel IV 15+, 16-
4-wire transmitter (separately powered):
measuring circuit: channel I 3+, 4-, channel II 7+, 8-, channel III 11+, 12-, channel IV 15+, 16-
Input resistance15 Ω (channel I: 3, 4; channel II: 7, 8; channel III: 11, 12; channel IV: 15, 16)
Line fault detectioncan be switched on/off for each channel via configuration tool , configurable via configuration tool
Short-circuitEx works settings: > 22 mA configurable between 0 ... 26 mA
Open-circuitEx works settings: < 1 mA configurable between 0 ... 26 mA
Transmitter supply voltagemin. 15 V at 20 mA
Transfer characteristics
Deviation
After calibration0.1 % of the signal range at 20 °C (68 °F)
Resolution12 Bit (0 ... 26 mA)
Refresh time80 ms
130 ms during HART
Indicators/settings
LED indicatorLED green: supply , flashing: calibration error
LED red: line fault , flashing: communication error
Directive conformity
Electromagnetic compatibility
Directive 2004/108/ECEN 61326-1
Conformity
Electromagnetic compatibilityNE 21
Degree of protectionIEC 60529
Ambient conditions
Ambient temperature-20 ... 60 °C (-4 ... 140 °F)
Storage temperature-25 ... 85 °C (-13 ... 185 °F)
Relative humidity95 % non-condensing
Shock resistanceshock type I, shock duration 11 ms, shock amplitude 50 m/s2, number of shock directions 6, number of shocks per direction 100
Vibration resistancefrequency range 5 ... 500 Hz, amplitude 5 ... 13.2 Hz ± 1.5 mm, 13.2 ... 100 Hz 1g, sweep rate 1 octave/min, duration 10 sweeps 5 Hz - 100 Hz - 5 Hz
Damaging gasdesigned for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protectionIP20 (module) , a separate housing is required acc. to the system description
Connectionremovable front connector with screw flange (accessory)
wiring connection via spring terminals (0.14 ... 1.5 mm2) or screw terminals (0.08 ... 1.5 mm2)
Massapprox. 750 g
Dimensions57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination CertificatePTB 97 ATEX 1074 U
MarkingEx-Hexagon II 2(1) G Ex d [ia] IIC , [Ex iaD]
Supply
Voltage28 V
Current90 mA
Power626 mW (linear characteristic)
Input
Voltage0.7 V
Current2.3 mA
Power2 mW (trapezoid characteristic curve)
Galvanic isolation
Input/power supply, internal bussafe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
Directive 94/9/ECEN 60079-0, EN 60079-1, EN 60079-11, EN 60079-26, EN 61241-0, EN 61241-11
International approvals
IECEx approvalpending

Classifications

SystemClasscode
ECLASS 13.027210120
ECLASS 12.027210101
ECLASS 11.027210120
ECLASS 10.0.127210120
ECLASS 9.027210120
ECLASS 8.027210120
ECLASS 5.127210120
ETIM 9.0EC001485
ETIM 8.0EC001485
ETIM 7.0EC001485
ETIM 6.0EC001485
ETIM 5.0EC001485
UNSPSC 12.139121008

Details: FB3205B

Datasheet: FB3205B

DatasheetTipo de archivoTamaño
Datasheet FB3205BPDF272 KB
Datenblatt FB3205BPDF270 KB

Documents: FB3205B

ManualsTipo de archivoTamaño
FB Hardware ManualPDF9157 KB
FB-Hardware-HandbuchPDF9182 KB
Instruction manuals
ИнструкцииPDF161 KB
Návod k poużitíPDF155 KB
Instruktions manualPDF154 KB
Instruction manualPDF147 KB
KasutusjuhendPDF149 KB
KäyttöohjePDF149 KB
Manuel d'instructionsPDF157 KB
BetriebsanleitungPDF148 KB
Οδηγίες χρήσηςPDF165 KB
HandleidingPDF156 KB
Instruction manual / BetriebsanleitungPDF154 KB
Használati útmutatóPDF155 KB
Manuale di istruzioniPDF156 KB
Lietošanas pamācībaPDF153 KB
Instrukciju vadovasPDF154 KB
Instrukcja obsługiPDF156 KB
Manual de instruçõesPDF156 KB
Manual de utilizarePDF154 KB
Návod na poużitiePDF155 KB
Navodila za uporaboPDF152 KB
Manual de instruccionesPDF157 KB
ManualPDF151 KB

Approvals+Certificates: FB3205B

CertificatesTipo de archivoTamaño
Europe PTB ATEX Category 2 GPDF2619 KB
Notas generales sobre la información de los productos de Pepperl+Fuchs

Pepperl+Fuchs SE
Lilienthalstraße 200
68307 Mannheim
Germany
info@de.pepperl-fuchs.com
phone +49 621 776-0

© 2024 Todos los derechos reservados

Pepperl + Fuchs es líder en el desarrollo y la fabricación de sensores electrónicos y componentes para el mercado de la automatización global. Su incesante innovación, calidad duradera y crecimiento constante garantizan el éxito continuado, desde hace más de 70 años. Pepperl + Fuchs emplea a 6.300 personas en todo el mundo y cuenta con fábricas en Alemania, EE.UU., Singapur, Hungría, Indonesia y Vietnam, la mayoría de ellas con certificado ISO 9001.