OMT300-R201-IEP-IO-0,3M-V1-L Distance sensor

Panoramica dei principali vantaggi

Medium design with versatile mounting options
Space-saving distance sensors in small standardized design
Multi Pixel Technology (MPT) - exact and precise signal evaluation
IO-Link interface for service and process data
Analog output 4 ... 20 mA

Mostra di più

Product photo: Distance sensor OMT300-R201-IEP-IO-0,3M-V1-L

Dimensions: Distance sensor OMT300-R201-IEP-IO-0,3M-V1-L

Nota

Tutti i documenti relativi ai prodotti, come ad esempio certificati, dichiarazioni di conformità ecc., pubblicati prima della conversione con il nome Pepperl+Fuchs GmbH o Pepperl+Fuchs AG, si applicano anche a Pepperl+Fuchs SE.

DE
EN
ES
FR

Scheda tecnica Funzione Classificazione Product Documentation Design / Simulation Certificazioni Software Prodotto correlati

Dati tecnici di OMT300-R201-IEP-IO-0,3M-V1-L

Distance sensor

Measuring range

100 ... 300 mm

Reference target

standard white, 100 mm x 100 mm

Light source

laser diode

Light type

modulated visible red light

Laser nominal ratings

Note		LASER LIGHT , DO NOT STARE INTO BEAM
Laser class		1
Wave length		680 nm
Beam divergence		> 5 mrad, d63 < 2,8 mm in the range of 350 mm ... 800 mm
Pulse length		5.5 µs
Repetition rate		approx. 2.4 kHz
max. pulse energy		< 40 nJ

Angle deviation

max. +/- 1.5 °

Diameter of the light spot

approx. 3 mm at a distance of 300 mm

Opening angle

approx. 0.3 °

Ambient light limit

EN 60947-5-2 : 45000 Lux

Resolution

0.1 mm

MTTF_d		470 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %

Operation indicator		LED green: constantly on - power on flashing (4Hz) - short circuit flashing with short break (1 Hz) - IO-Link mode
Function indicator		LED yellow: constantly on - switch output active constantly off - switch output inactive
Control elements		Teach-In key
Control elements		5-step rotary switch for operating modes selection

Operating voltage	U_B	18 ... 30 V DC
Ripple		max. 10 %
No-load supply current	I₀	< 18 mA at 24 V supply voltage
Protection class		III

Interface type		IO-Link ( via C/Q = pin 4 )
IO-Link revision		1.1
Device profile		Identification and diagnosis Smart Sensor type 0/type 3.3
Device ID		0x11191B (1120539)
Transfer rate		COM2 (38.4 kBit/s)
Min. cycle time		3 ms
Process data width		Process data input 4 byte Process data output 2 bits
SIO mode support		yes
Compatible master port type		A

Switching type		The default setting is: C/Q - Pin4: NPN normally open, PNP normally closed, IO-Link I—Pin2: analog output 4...20 mA
Signal output		1 push-pull output , 1 analog output , short-circuit-proof, reverse polarity protection, surge-proof
Switching voltage		max. 30 V DC
Switching current		max. 100 mA , resistive load
Usage category		DC-12 and DC-13
Voltage drop	U_d	≤ 1.5 V DC
Response time		2 ms

Output type

1 current output: 4 ... 20 mA

Load resistor

> 1 kΩ voltage output ; ≤ 470 Ω current output

Recovery time

2 ms

Communication interface		IEC 61131-9
Product standard		EN 60947-5-2
Laser safety		EN 60825-1:2014

Temperature drift		0.05 %/K
Warm up time		5 min
Repeat accuracy		< 0.5 %
Linearity error		0.5 %

UL approval		E87056 , cULus Listed , class 2 power supply , type rating 1
CCC approval		CCC approval / marking not required for products rated ≤36 V
FDA approval		IEC 60825-1:2014 Complies with 21 CFR 1040.10 and 1040.11 except for conformance with IEC 60825-1 Ed. 3 as described in Laser Notice 56, dated May 8, 2019.

Ambient temperature		10 ... 50 °C (50 ... 122 °F)
Storage temperature		-40 ... 70 °C (-40 ... 158 °F)

Degree of protection

IP67 / IP69 / IP69K

Connection

300 mm fixed cable with M12 x 1, 4-pin connector

Material

Housing		PC (Polycarbonate)
Optical face		PMMA

Mass

approx. 55 g

Dimensions

Height		61.7 mm
Width		15 mm
Depth		41.7 mm

Cable length

0.3 m

Note generali