UC800-F77S-IU-IO-V31 Ultrasonic sensor

Panoramica dei principali vantaggi

IO-Link interface for parameterization
Programmable via DTM with PACTWARE
Selectable sound lobe width
Synchronization options
Temperature compensation
Analog output

Mostra di più

Product photo: Ultrasonic sensor UC800-F77S-IU-IO-V31

Dimensions: Ultrasonic sensor UC800-F77S-IU-IO-V31

Nota

Tutti i documenti relativi ai prodotti, come ad esempio certificati, dichiarazioni di conformità ecc., pubblicati prima della conversione con il nome Pepperl+Fuchs GmbH o Pepperl+Fuchs AG, si applicano anche a Pepperl+Fuchs SE.

DE
EN
ES
FR
JA

Scheda tecnica Classificazione Informative Literature Product Documentation Design / Simulation Certificazioni Software Prodotto correlati

Dati tecnici di UC800-F77S-IU-IO-V31

Single head system

Sensing range		60 ... 800 mm
Adjustment range		70 ... 800 mm
Dead band		0 ... 60 mm
Standard target plate		100 mm x 100 mm
Transducer frequency		approx. 255 kHz
Response delay		minimum : 13 ms factory setting: 49 ms
Sensor cycle time		≥ 13 ms (factory setting) ; programmable to 60 s

Non-volatile memory		EEPROM
Write cycles		300000

LED green		solid: power on flashing: standby mode or IO-Link communication
LED yellow		solid: object in evaluation range flashing: programming of the limits, object detected
LED red		solid: fault flashing: programming limits, object not detected

Operating voltage	U_B	18 ... 30 V DC , ripple 10 %_SS
No-load supply current	I₀	≤ 50 mA
Power consumption	P₀	≤ 500 mW
Time delay before availability	t_v	≤ 300 ms

Interface type

IO-Link (available after activation via programming button until next reset)

Input/output type

1 synchronization connection, bidirectional

0 Level		0 ... 1 V
1 Level		2.5 V ... U_B
Input impedance		> 22 kΩ
Output current		current source < 2.5 mA
Pulse length		≥ 1 ms with external control, low active

Synchronization frequency

Common mode operation		≤ 82 Hz
Multiplex operation		≤ 82 Hz / n , n = number of sensors , n ≤ 10

Output type		1 analog output 0 (4) ... 20 mA or 1 analog output 0 ... 10 V
Resolution		current output: evaluation range [mm]/3200 but ≥ 0.35 mm voltage output: evaluation range [mm]/4000 but ≥ 0.35 mm
Deviation of the characteristic curve		≤ ± 1 % of full-scale value
Repeat accuracy		≤ ± 0.1 % of full-scale value
Load impedance		current output: ≤ 500 Ohm voltage output: ≥ 1000 Ohm
Temperature influence		≤ ± 0.75 % of the end value (with temperature compensation) from 10 minutes after switching on the sensor ; 0.17 %/K (without temperature compensation)

Standard conformity

Standards

EN IEC 60947-5-2:2020
IEC 60947-5-2:2019
EN 60947-5-7:2003
IEC 60947-5-7:2003
IEC 61131-9:2013

UL approval		cULus Listed, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated ≤36 V

Ambient temperature		current output -25 ... 60 °C (-13 ... 140 °F) voltage output -25 ... 70 °C (-13 ... 158 °F) When fixing with one M18 nut, the temperature range for each begins with 0 °C (32 °F).
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)

Connection type

Connector plug M8 x 1 , 4-pin

Degree of protection

IP67

Material

Housing		Polycarbonate
Transducer		epoxy resin/hollow glass sphere mixture; polyurethane foam

Installation position

any position

Mass

13 g

Tightening torque, fastening screws

with M3 nuts max. 0.2 Nm
with M18 nuts max. 1 Nm

Dimensions

Height		31 mm
Width		21 mm
Length		23 mm

Output		near limit: 70 mm far limit: 800 mm Output mode: rising ramp output type: 4 ... 20 mA
Beam width		wide

Scope of delivery

1 Nut plastic

Note generali