Teknisk support Industrielle sensorer
Kundeservice, eksplosjonsbeskyttelse

Diffuse mode sensor WTS10-12-4016/103/105

WTS10-12-4016/103/105
  • Specifically for quality checks on welding caps
  • Upper and lower welding caps checked simultaneously
  • High position and angle tolerance insensitivity of the welding cap
  • Stability alarm indication
  • Scratch resistant mineral glass lens

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Last ned komplett datablad som PDF:


Datablad utdrag: Tekniske data for  WTS10-12-4016/103/105

Produktbeskrivelse
Diffuse mode sensor
General specifications
Detection range2 ... 12 mm
Reference targetCopper welding-electrode Diameter: 16 mm , Front end: 6 mm
Light sourceLED
Light typemodulated visible red light , 640 nm
Ambient light limitcontinuous light 40000 Lux , Modulated light 5000 Lux
Tilting angle± 1.5 °
Position tolerance± 2 mm
Indicators/operating means
Operation indicatorLED green: Power on
Function indicatorLED yellow: switching state
LED red: Stability alarm indicator
Teach-in indicatorLED, green/yellow flashing (approx. 4 Hz)
Teach Error:LED green/yellow non equiphase flashing; 8.0 Hz
Control elementsTeach-In key
Electrical specifications
Operating voltage10 ... 30 V DC
No-load supply current≤ 70 mA
Input
Function inputEnable keys (EK)
Output
Switching typelight-on
Signal outputswitching output PNP NO contact AND logic coupling of both sensor channels short-circuit protected reverse polarity protected
Switching currentmax. 100 mA
Switching frequency100 Hz
Response time5 ms
Conformity
Product standardEN 60947-5-2
Compliance with standards and directives
Standard conformity
Shock and impact resistanceIEC / EN 60068. half-sine, 50 g in each X, Y and Z directions
Vibration resistanceIEC / EN 60068-2-6. Sinus. 10 -150 Hz, 5 g in each X, Y and Z directions
Approvals and certificates
Protection classII, rated voltage ≤ 250 V AC with pollution degree 1-2 according to IEC 60664-1
UL approvalcULus Listed
CCC approvalCCC approval / marking not required for products rated ≤36 V
Ambient conditions
Ambient temperature0 ... 50 °C (32 ... 122 °F)
The switching accuracy will remain, if the temperature after Teach-In does not varies more than ±7 °C
Storage temperature-20 ... 70 °C (-4 ... 158 °F)
Mechanical specifications
Degree of protectionIP67
Connection5-pin, M12 x 1 connector
Material
HousingPC + ABS
Optical faceScratch resistant mineral glass lens
Mass80 g

Classifications

SystemClasscode
ECLASS 13.027270903
ECLASS 12.027270903
ECLASS 11.027270903
ECLASS 10.0.127270903
ECLASS 9.027270903
ECLASS 8.027270903
ECLASS 5.127270903
ETIM 9.0EC001821
ETIM 8.0EC001821
ETIM 7.0EC001821
ETIM 6.0EC001821
ETIM 5.0EC001821
UNSPSC 12.139121528

Details: WTS10-12-4016/103/105

Function

The welding tip sensor WTS10 series is a contrast evaluation sensor with a large and homogeneous light spot fitted to check the quality of the welding cap's face after milling of the welding tip and which is widely used for industrial welding robots.

After the milling process of the welding cap, both tips of the welding gun are inspected and defects such as inclusions, faulty milling or burrs are detected.

Simultaneous control of the quality of both welding tip caps with one sensor is possible by providing two optical outputs on either side of the sensor housing.

The WTS10 features an extended detection area of 11 mm diameter, an uniform lightspot over the full sensing range due to coaxial optics beam path, a new display concept, high switching accuracy, a homogenous light spot and improved position and tilting angle tolerance.

Product Documentation: WTS10-12-4016/103/105

Velg språk:
Brief InstructionsSpråkFiltypeFilstørrelse
Instruction leaflet / BeipackzettelALLPDF527 KB

Design / Simulation: WTS10-12-4016/103/105

Velg språk:
CADSpråkFiltypeFilstørrelse
CAD 3-D / CAD 3-DALLSTP1366 KB
CAD Portal / CAD PortalALLLINK---

Approvals: WTS10-12-4016/103/105

Velg språk:
Declaration of ConformitySertifikatnummerSpråkFiltypeFilstørrelse
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)DOC-2236CALLPDF226 KB
UK Declaration of Conformity (P+F) / UK-Konformitäterklärung (P+F)DOC-6936ALLPDF223 KB

Relaterte produkter: WTS10-12-4016/103/105

Accessories

Female cordset single-ended M12 straight A-coded, 5-pin, PVC cable greyfa

Female cordset single-ended M12 straight A-coded, 5-pin, PUR cable greyfa

Female cordset single-ended M12 angled A-coded, 5-pin, PVC cable greyfa
Mounting bracket for sensors of WTS10 seriesfa
Fotoceller i R10x- og R20x-serien

For første gang er en konsekvent løsningsserie med fotoelektriske funksjonsprinsipper og innovative teknologier tilgjengelig i identiske kapslinger. Brukere drar fordel av et uniformt driftskonsept over hele porteføljen. Oppdag seriene R100, R101, R103, R200 og R201 ...

ML100-fotocelle

Uansett om det er glass, silisiumskiver eller kretskort: Fotocellene i ML100-serien er spesiallaget for å oppfylle kravene til komplekse registreringsoppgaver. Lær mer om porteføljen ...