Servisní linka pro průmyslové snímače
Zeptejte se odborníků
Servisní linka ochrany před výbuchem
Zeptejte se odborníků
Převodníky signálů
Nedostupné pro prodej
Nedostupné pro prodej

SMART Transmitter Power Supply HiD2030SK

HiD2030SK
  • 2-channel isolated barrier
  • 24 V DC supply (bus powered)
  • 2-wire SMART transmitters or current sources
  • Usable as signal splitter (1 input and 2 outputs)
  • Dual output 4 mA ... 20 mA, current sink
  • Line fault detection (LFD)
  • Up to SIL 2 (SC 3) acc. to IEC/EN 61508

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Výňatek z katalogového listu: Technická data   HiD2030SK

General specifications
Signal typeAnalog input
Functional safety related parameters
Safety Integrity Level (SIL)SIL 2
Systematic capability (SC)SC 3
Supply
ConnectionSL1: 1a(-), 1b(-); 2a(+), 2b(+)
Rated voltage19 ... 30 V DC bus powered via Termination Board
Rated current14 mA at 24 V, 250 Ω load, 20 mA output (per channel)
Power dissipation350 mW at 24 V, 250 Ω load, 20 mA output (per channel)
Input
Connection sidefield side
ConnectionSL2: 5a(+), 5b, 7a(-); 1a(+), 1b, 3b(-)
Input current4 ... 20 mA , current limit approx. 26 mA typ.
Input resistance< 40 Ω , for current source
Ripple10 mV eff
Voltagemin. 15.5 V at 20 mA
Communicationpass-through of HART signal to safe area
The current sink terminals 4, 7 and 5, 6 do not pass HART signal to safe area.
Output
Connection sidecontrol side
ConnectionSL1: 8a(+), 7a(-); 10a(+), 9a(-)
Outputsink mode from external supply
Output signal4 ... 20 mA
Voltageworking voltage 7 ... 30 V
Response time70 ms , 10 ... 90 % step change
Signal levelno fault: 1 mA ... 23.5 mA input current
fault detection: < 0.2 mA or > 24 mA input current
Fault indication output
ConnectionSL1: 6b
Output typeopen collector transistor (common to both channels)
fault bus signal, collective error message
Transfer characteristics
Deviationat 20 °C (68 °F), 0/4 ... 20 mA
≤ 20 µA incl. calibration, linearity, hysteresis, loads and fluctuations of supply voltage
Influence of ambient temperature≤ 2 µA/K
Frequency rangefield side into the control side: bandwidth with 0.5 Vpp signal 0 ... 3 kHz (-3 dB)
control side into the field side: bandwidth with 0.5 Vpp signal 0 ... 3 kHz (-3 dB)
Galvanic isolation
Input/Outputbasic insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff
Input/power supplyreinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff
Output/power supplybasic insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff
Output/Outputfunctional insulation, rated insulation voltage 50 V AC
Indicators/settings
Display elementsLEDs
Labelingspace for labeling at the front
Directive conformity
Electromagnetic compatibility
Directive 2014/30/EUEN 61326-1:2013 (industrial locations)
Conformity
Electromagnetic compatibilityNE 21:2017
EN 61326-3-2:2018
Degree of protectionIEC 60529:2001
Protection against electrical shockUL 61010-1:2012
Ambient conditions
Ambient temperature-40 ... 60 °C (-40 ... 140 °F)
Relative humidity5 ... 90 %, non-condensing up to 35 °C (95 °F)
Mechanical specifications
Degree of protectionIP20
Mass140 g
Dimensions18 x 114 x 130 mm (0.7 x 4.5 x 5.1 inch) (W x H x D)
Height114 mm
Width18 mm
Depth130 mm
Mountingon termination board
Codingpin 1 and 3 trimmed
For further information see system description.
Data for application in connection with hazardous areas
EU-type examination certificateCSANe 21 ATEX 2149 X
MarkingEx-Hexagon II (1)G [Ex ia Ga] IIC
Ex-Hexagon II (1)D [Ex ia Da] IIIC
Ex-Hexagon I (M1) [Ex ia Ma] I
InputEx ia, Ex iaD
Voltage26 V
Current93 mA
Power605 mW
Supply
Maximum safe voltage250 V AC (Attention! Um is no rated voltage.)
Galvanic isolation
Input/inputsafe electrical isolation acc. to EN 60079-11:2007, voltage peak value 60 V
Input/Outputsafe electrical isolation acc. to IEC 60079-11:2007, voltage peak value 375 V
Input/power supplysafe electrical isolation acc. to IEC 60079-11:2007, voltage peak value 375 V
Directive conformity
Directive 2014/34/EUEN 60079-0:2018 , EN 60079-11:2012
International approvals
CSA approvalCoC 80072560 (cCSAus)
Control drawing116-0486
IECEx approval
IECEx certificateIECEx CSAE 21.0010X
IECEx marking[Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I
General information
Supplementary informationObserve the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

Classifications

SystemClasscode
ECLASS 13.027210119
ECLASS 12.027210119
ECLASS 11.027210119
ECLASS 10.0.127210119
ECLASS 9.027210119
ECLASS 8.027210119
ECLASS 5.127210119
ETIM 9.0EC001485
ETIM 8.0EC001485
ETIM 7.0EC001485
ETIM 6.0EC001485
ETIM 5.0EC001485
UNSPSC 12.132101514

Details: HiD2030SK

Datasheet: HiD2030SK

DatasheetTyp souboruVelikost souboru
Datasheet HiD2030SKPDF1150 KB
Fiche de données HiD2030SKPDF1157 KB
Datenblatt HiD2030SKPDF1153 KB
Datasheet HiD2030SKPDF1205 KB
Hoja de datos HiD2030SKPDF1159 KB

Documents: HiD2030SK

ManualsTyp souboruVelikost souboru
System ManualPDF5438 KB
SystemhandbuchPDF5450 KB
Instruction manuals
ИнструкцииPDF143 KB
Návod k poużitíPDF138 KB
Instruktions manualPDF137 KB
Instruction manualPDF146 KB
KasutusjuhendPDF134 KB
KäyttöohjePDF133 KB
Manuel d'instructionsPDF138 KB
BetriebsanleitungPDF147 KB
Οδηγίες χρήσηςPDF145 KB
HandleidingPDF138 KB
Instruction manual / BetriebsanleitungPDF137 KB
Használati útmutatóPDF138 KB
Manuale di istruzioniPDF136 KB
Lietošanas pamācībaPDF137 KB
Instrukciju vadovasPDF138 KB
Instrukcja obsługiPDF139 KB
Manual de instruçõesPDF137 KB
Manual de utilizarePDF137 KB
Návod na poużitiePDF138 KB
Navodila za uporaboPDF135 KB
Manual de instruccionesPDF137 KB
ManualPDF135 KB
Documents
Functional Safety ManualPDF1979 KB
Handbuch funktionale SicherheitPDF1991 KB

CAD+CAE: HiD2030SK

CADTyp souboruVelikost souboru
CAD 2-D / CAD 2-DZIP16364 KB
Všeobecné poznámky týkající se produktů společnosti Pepperl+Fuchs
Safety Products Selector

Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.

Pepperl+Fuchs s.r.o.
Pod Vodárenskou věží 4
18208 Praha 8
Czech Republic
info@cz.pepperl-fuchs.com
phone +420 225 989 180

© 2024 Všechna práva vyhrazena

Pepperl+Fuchs je přední vývojář a výrobce průmyslových senzorů a komponentů pro světový trh automatizace. Neustálé inovace, trvalé kvalitní a stálý růst zaručuje mnoho úspěchů přes více než 70 let. Pepperl+Fuchs zaměstnává 6300 lidí po celém světě a má výrobní závody v Německu, USA, Singapuru, Maďarsku, Indonésii a Vietnamu, které podléhají ISO 9001.