Servisní linka pro průmyslové snímače
Servisní linka ochrany před výbuchem

Ultrasonic sensor UC800-F77S-EP-IO-V31

  • IO-Link interface for service and process data
  • Programmable via DTM with PACTWARE
  • Continuous distance value via IO-Link process data
  • Selectable sound lobe width
  • Synchronization options
  • Temperature compensation
  • Push-pull output

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Stáhněte si kompletní katalogový list ve formátu PDF:

Výňatek z katalogového listu: Technická data   UC800-F77S-EP-IO-V31

Popis produktu
Single head system
General specifications
Sensing range60 ... 800 mm
Adjustment range70 ... 800 mm
Dead band0 ... 60 mm
Standard target plate100 mm x 100 mm
Transducer frequencyapprox. 255 kHz
Response delayminimum : 13 ms
factory setting: 49 ms
Sensor cycle time≥ 13 ms (factory setting) ;
programmable to 60 s
Non-volatile memoryEEPROM
Write cycles300000
Indicators/operating means
LED greensolid: power on
flashing: standby mode or IO-Link communication
LED yellowsolid: object in evaluation range
flashing: switch point programming, object detected
LED redsolid: error
flashing: switch point programming, object not detected
Electrical specifications
Operating voltage10 ... 30 V DC , ripple 10 %SS
No-load supply current≤ 40 mA
Power consumption≤ 400 mW
Time delay before availability≤ 300 ms
Interface typeIO-Link (via C/Q = Pin 4)
IO-Link revision1.1
Device profileSmart Sensor
Device ID0x300302 (3146498)
Transfer rateCOM2 (38.4 kBit/s)
Min. cycle time2.3 ms
Process data width16 bit
SIO mode supportyes
Compatible master port typeA
Input/output type1 synchronization connection, bidirectional
0 Level0 ... 1 V
1 Level2.5 V ... UB
Input impedance> 22 kΩ
Output currentcurrent source < 2.5 mA
Pulse length≥ 1 ms with external control, low active
Synchronization frequency
Common mode operation≤ 82 Hz
Multiplex operation≤ 82 Hz / n , n = number of sensors , n ≤ 10
Output type1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected
Rated operating current100 mA , short-circuit/overload protected
Voltage drop≤ 2.5 V
Repeat accuracy≤ ± 0.1 % of full-scale value
Switching frequencyfactory setting: 12 Hz programmable max. 27 Hz
Range hysteresis1 % of the adjusted operating range (default settings), programmable , min. 1 mm
Temperature influence≤ ± 0.75 % of the end value (with temperature compensation) from 10 minutes after switching on the sensor ; 0.17 %/K (without temperature compensation)
Compliance with standards and directives
Standard conformity
StandardsEN IEC 60947-5-2:2020
IEC 60947-5-2:2019
IEC 61131-9:2013
Approvals and certificates
UL approvalcULus Listed, Class 2 Power Source
CCC approvalCCC approval / marking not required for products rated ≤36 V
Ambient conditions
Ambient temperature-25 ... 70 °C (-13 ... 158 °F)
When fixing with one M18 nut, the temperature range begins with 0 °C (32 °F).
Storage temperature-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection typeConnector plug M8 x 1 , 4-pin
Degree of protectionIP67
Transducerepoxy resin/hollow glass sphere mixture; polyurethane foam
Installation positionany position
Mass13 g
Tightening torque, fastening screwswith M3 nuts max. 0.2 Nm
with M18 nuts max. 1 Nm
Height31 mm
Width21 mm
Length23 mm
Factory settings
Outputnear switch point: 70 mm
far switch point: 800 mm
Output mode: Window mode
Output logic: normally open
Beam widthwide


ECLASS 13.027272803
ECLASS 12.027272803
ECLASS 11.027272803
ECLASS 10.0.127272803
ECLASS 9.027272803
ECLASS 8.027272803
ECLASS 5.127272803
ETIM 9.0EC001849
ETIM 8.0EC001849
ETIM 7.0EC001849
ETIM 6.0EC001849
ETIM 5.0EC001849
UNSPSC 12.141111960

Details: UC800-F77S-EP-IO-V31

Informative Literature: UC800-F77S-EP-IO-V31

Výběr jazyka:
LiteratureJazykTyp souboruVelikost souboru
Application Report - Reliable Detecting Foil Tears in Battery Cell ManufacturingENGPDF163 KB
Application Report - Ultrasonic sensors measure roll diameter and detect web breakENGPDF172 KB

Product Documentation: UC800-F77S-EP-IO-V31

Výběr jazyka:
Product informationJazykTyp souboruVelikost souboru
Installation and user instructions for offline parameterization of IO-Link sensorsENGPDF1788 KB
Brief Instructions
Commissioning instruction for UC-F77*-EP* / Inbetriebnahmeanleitung für UC-F77*-EP*ALLPDF445 KB
Manual UC***-F77 Series Parameterization of Ultrasonic Sensors with IO-Link InterfaceENGPDF4224 KB

Design / Simulation: UC800-F77S-EP-IO-V31

Výběr jazyka:
CADJazykTyp souboruVelikost souboru
CAD Portal / CAD PortalALLLINK---
CAE EPLAN Data Portal / CAE EPLAN Data PortalALLLINK---

Approvals: UC800-F77S-EP-IO-V31

Výběr jazyka:
CertificatesČíslo certifikátuJazykTyp souboruVelikost souboru
Canada USA UL Ordinary LocationUL-US-2140030-0 / UL-CA-2133555-0ALLPDF546 KB
IO-Link Manufacturer DeclarationCERT-4363ALLPDF254 KB
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)DOC-3523BALLPDF47 KB
UK Declaration of Conformity (P+F) / UK-Konformitäterklärung (P+F)DOC-5507ALLPDF40 KB

Software: UC800-F77S-EP-IO-V31

Výběr jazyka:
Device Description Files/DriversInformace o uvolněníTyp souboruVelikost souboru
IODD for UC*-F77*-EP-IO / IODD für UC*-F77*-EP-IOV1.01.000 / 2020-10-01ZIP512 KB
DTM (Device Type Manager) Package for UC*-F77* ultrasonic sensors / DTM (Device Type Manager) Package für UC*-F77* UltraschallsensorenV1.2.0.2 / 09-08-2022ZIP12278 KB
Software Tools
IO-Link Offline Parameterization Tool / IO-Link Offline-ParametriertoolV1.00.006 / 2022-07-10ZIP96138 KB

Související produkty: UC800-F77S-EP-IO-V31


Female cordset single-ended M8 straight A-coded, 4-pin, PVC cable greyfa

EtherNet/IP IO-Link master with 8 inputs/outputsfa

PROFINET IO IO-Link master with 8 inputs/outputsfa
Cordset M8 socket straight to M12 plug straight A-coded, 4-pin, PVC cable greyfa
Mounting aid for ML7 and ML8 series, Mounting bracketfa
Mounting aid for ML7 and ML8 series, Mounting bracketfa
Ethernet IO-Link module with 8 inputs/outputsfa
Ethernet IO-Link module with 8 inputs/outputsfa
EtherNet/IP IO-Link master with 8 inputs/outputs, DIN rail, push-in connectorsfa
EtherNet/IP IO-Link master with 8 inputs/outputs, DIN rail, screw terminalfa
PROFINET IO IO-Link master with 8 inputs/outputs, DIN rail, push-in terminalsfa
PROFINET IO IO-Link master with 8 inputs/outputs, DIN rail, screw terminalfa
IO-Link master, supply via USB port or separate power supply, LED indicators, M12 plug for sensor connectionfa
Systém senzorů USi-safety

Systém ultrazvukových senzorů USi-safety posouvá bezpečnostní aplikace na novou úroveň – ať již se jedná o aplikace v náročných, prašných prostředích nebo ve venkovních prostorách.

Společnost Pepperl+Fuchs vám nabízí různé dokumenty ke stažení, které obsahují poznatky o ultrazvukových senzorech.